You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
what do you guys think about this "curr_samp_volt "? by jem on Thu, 2019-08-08 14:45 |
by jem Thu, 2019-08-08 14:45 |
VESC Firmware | ||
|
VESC Calculator by lmochsner on Thu, 2020-04-02 05:13 |
by lmochsner Thu, 2020-04-02 05:13 |
General discussion | ||
|
Cannot upgrade firmware by greensightag.com on Fri, 2018-04-27 02:32 |
by greensightag.com Fri, 2018-04-27 02:34 |
VESC Firmware | ||
|
Integration of VESC with a display using I2C by dsuresh on Thu, 2021-05-20 19:32 |
by dsuresh Thu, 2021-05-20 19:32 |
General discussion | ||
|
Vesc WS2812b led issues & support by Ash on Tue, 2019-11-12 08:40 |
by Ash Tue, 2019-11-12 14:13 |
General discussion | ||
|
PPM Pulselength mapping by Shaftdriver on Tue, 2022-10-04 17:18 |
by Shaftdriver Tue, 2022-10-04 17:18 |
VESC Tool | ||
|
VESC with 3 shunt by _johnny_ on Fri, 2019-11-01 18:57 |
by _johnny_ Fri, 2019-11-01 18:57 |
Third Party Hardware | ||
|
weird ADC problem that only appears with 48V battery by kylerlaird on Sun, 2021-01-31 12:02 |
by kylerlaird Sun, 2021-01-31 12:02 |
VESC Original Hardware | ||
|
Input Setup Wizard - Update Firmware by pmg on Thu, 2020-02-13 09:54 |
by pmg Thu, 2020-02-13 09:54 |
VESC Tool | ||
|
Fault: FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 on VESC 6 by Jackl on Tue, 2019-05-28 14:48 |
by Jackl Tue, 2019-05-28 14:48 |
VESC Original Hardware | ||
|
12v(3s) Input to VESC 75/250 by AliBarrett10 on Wed, 2021-03-24 14:36 |
by AliBarrett10 Wed, 2021-03-24 16:19 |
General discussion | ||
|
Tenka esc in need of a reliable vesc tool by Vincent Gervais on Tue, 2021-12-21 00:48 |
by Vincent Gervais Tue, 2021-12-21 00:48 |
Third Party Hardware | ||
|
Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM by PaulMakesThings on Fri, 2022-08-05 11:06 |
by PaulMakesThings Fri, 2022-08-05 11:06 |
General discussion | ||
|
I need VESC Tool Version 1.13, please. by Astropower on Sun, 2019-09-08 18:22 |
by Astropower Sun, 2019-09-08 18:22 |
VESC Tool | ||
|
Steering channel (dual vesc setup via CAN bus) by fender90 on Sun, 2020-04-26 03:47 |
by fender90 Sun, 2020-04-26 03:47 |
Feature Requests | ||
|
controller_id on COMM_GET_IMU_DATA by andrea.scipione on Sun, 2020-11-22 19:07 |
by andrea.scipione Sun, 2020-11-22 19:07 |
Feature Requests | ||
|
Ground Loop question by a.smith on Wed, 2021-06-23 13:25 |
by a.smith Wed, 2021-06-23 13:25 |
General discussion | ||
|
Rion Tronic 250/ Focer3.1 using TC leads to explosion! by Drcfan on Mon, 2022-11-14 23:12 |
by Drcfan Tue, 2022-11-15 14:05 |
General discussion | ||
|
Latest VESC FW completely broken on 4.12 hardware by chris1seto on Fri, 2019-04-05 17:41 |
by chris1seto Fri, 2019-04-05 17:54 |
VESC Firmware | ||
|
Where to find codelines for speed and position control structure by kianK on Tue, 2022-03-01 15:25 |
by kianK Thu, 2022-03-03 12:23 |
VESC Firmware |
Pages
