You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Building the vesc firmware in Chibi Studio by chris1seto on Sat, 2019-01-12 02:36 |
1 |
by kinzma Thu, 2019-02-14 09:42 |
General discussion | |
|
Always get Fault:DRV in FOC mode during startup . by stone_1706 on Sat, 2019-02-02 17:35 |
3 |
by stone_1706 Tue, 2019-02-12 03:20 |
General discussion | |
|
Sub zero temperature VESC412 issues by jetigm on Fri, 2019-02-08 21:12 |
3 |
by sam.vanratt Sun, 2019-02-10 14:07 |
General discussion | |
|
Dual brushed motors from 1 R/C stick? by VESC1 on Thu, 2019-01-31 06:19 |
5 |
by sam.vanratt Sun, 2019-02-03 16:30 |
General discussion | |
|
Fault:DRV8302 DUAL V4 by Lzx19961014 on Tue, 2018-09-04 11:48 |
3 |
by stone_1706 Sat, 2019-02-02 17:09 |
General discussion | |
|
VESC Tool Instructions by brschaefer74 on Fri, 2019-01-25 03:49 |
4 |
by sam.vanratt Sat, 2019-01-26 12:52 |
General discussion | |
|
VESC and Motors for sale. by raess on Thu, 2019-01-24 22:41 |
by raess Thu, 2019-01-24 22:41 |
General discussion | ||
|
Connect both hall and incremental quadrature encoders by vpl on Tue, 2019-01-15 14:24 |
1 |
by galp Thu, 2019-01-24 14:25 |
General discussion | |
|
Increasing low rpm torque in FOC mode by galp on Mon, 2019-01-21 18:15 |
1 |
by sam.vanratt Thu, 2019-01-24 00:02 |
General discussion | |
|
Separate Deadband for ADC2? by striderkent on Wed, 2019-01-23 16:31 |
by striderkent Wed, 2019-01-23 16:31 |
General discussion | ||
|
Angle offset detection by Gas_Sn4ke on Mon, 2019-01-21 07:09 |
by Gas_Sn4ke Mon, 2019-01-21 07:09 |
General discussion | ||
|
Change RPM of motor by Gas_Sn4ke on Wed, 2019-01-16 03:51 |
2 |
by Shaik Siraaj Thu, 2019-01-17 11:14 |
General discussion | |
|
Vesc 6 motor setup fault by Davo69URX on Wed, 2017-11-29 09:22 |
21 |
by Tresor Wed, 2019-01-16 12:38 |
General discussion | |
|
Upload bootloader to new MCU by Jessica on Fri, 2019-01-11 14:43 |
7 |
by Jessica Wed, 2019-01-16 09:07 |
General discussion | |
|
4kw BLDC hybrid system help by thardi10 on Tue, 2019-01-08 17:06 |
2 |
by frank Tue, 2019-01-15 22:15 |
General discussion | |
|
Can not adjust the RPM on my 1350 w motor by Arne Norway on Wed, 2019-01-09 18:47 |
6 |
by sam.vanratt Sun, 2019-01-13 13:36 |
General discussion | |
|
Dead VESC. Power up when motor is spinning. by Bor Zabric on Mon, 2018-10-08 10:16 |
4 |
by striderkent Fri, 2019-01-11 18:46 |
General discussion | |
|
VESC acceleration control on setRPM by fourchette on Tue, 2019-01-08 12:02 |
3 |
by fourchette Wed, 2019-01-09 10:38 |
General discussion | |
|
Fast Startup problem by sam.vanratt on Thu, 2019-01-03 17:56 |
7 |
by sam.vanratt Sun, 2019-01-06 23:25 |
General discussion | |
|
ADC1 problems with Firmware/Hardware issue? by sam.vanratt on Thu, 2018-12-27 22:31 |
4 |
by sam.vanratt Thu, 2019-01-03 17:46 |
General discussion |
Pages
