You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM by PaulMakesThings on Fri, 2022-08-05 11:06 |
by PaulMakesThings Fri, 2022-08-05 11:06 |
General discussion | ||
|
temperature compensation make sense？ by alexshen2012 on Thu, 2022-08-04 08:28 |
1 |
by alexshen2012 Thu, 2022-08-04 09:17 |
General discussion | |
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset on Thu, 2022-08-04 01:44 |
by liminalsunset Thu, 2022-08-04 01:44 |
General discussion | ||
|
Lanyard kill switch by craig w on Mon, 2022-01-03 09:30 |
3 |
by ewakegermanyhq Wed, 2022-08-03 16:55 |
General discussion | |
|
Under rated VESC for motor, problem? by Alistair Goodman on Wed, 2022-08-03 12:53 |
2 |
by Alistair Goodman Wed, 2022-08-03 15:27 |
General discussion | |
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 on Mon, 2022-08-01 18:08 |
by moose09876 Mon, 2022-08-01 18:08 |
General discussion | ||
|
Dynamic Braking with resistor by jwhall on Sun, 2022-07-31 19:58 |
by jwhall Sun, 2022-07-31 23:51 |
General discussion | ||
|
Controling the Vesc via Uart and Matlab? by Michael Hamm on Mon, 2022-01-24 16:47 |
1 |
by Fikret Sonmez Sat, 2022-07-30 06:14 |
General discussion | |
|
VESC with asynchronous motors by afbbfa on Fri, 2022-07-29 22:51 |
by afbbfa Fri, 2022-07-29 22:51 |
General discussion | ||
|
Regen not enabling! by Fpvlee on Sun, 2021-07-25 01:11 |
3 |
by lilysmith1098 Fri, 2022-07-29 09:45 |
General discussion | |
|
Trampa 100/250 with Cyc x1pro motor high Rpm issue PLZ Help :) by Asi on Thu, 2022-07-28 10:08 |
2 |
by Asi Thu, 2022-07-28 16:12 |
General discussion | |
|
Current became not stable over time by AnthonyFR on Mon, 2022-07-25 23:21 |
1 |
by frank Wed, 2022-07-27 20:35 |
General discussion | |
|
Rc controller more than one input ? by zebb.guy@moshon... on Tue, 2022-07-26 14:51 |
2 |
by zebb.guy@moshon... Wed, 2022-07-27 17:22 |
General discussion | |
|
Kill switch by 999dom999 on Thu, 2022-04-07 10:44 |
7 |
by hnr_engineer Tue, 2022-07-26 06:07 |
General discussion | |
|
Enable/Disable VESC Response to Incoming PWM Control by gazlinux on Sun, 2022-03-06 19:13 |
2 |
by hnr_engineer Tue, 2022-07-26 05:39 |
General discussion | |
|
Compiling on windows by j.m on Wed, 2021-03-17 10:22 |
1 |
by joku_cale Fri, 2022-07-22 20:03 |
General discussion | |
|
ignore this by tobe81cwb on Tue, 2022-06-21 18:51 |
by tobe81cwb Tue, 2022-07-19 16:44 |
General discussion | ||
|
Robot traction drive application by cjmssmd on Tue, 2022-07-19 03:37 |
1 |
by cjmssmd Tue, 2022-07-19 16:39 |
General discussion | |
|
VESC specialist required. by BlackPanthera on Mon, 2022-07-18 17:11 |
by BlackPanthera Mon, 2022-07-18 17:11 |
General discussion | ||
|
LISP_BM and CAN by kinzma on Mon, 2022-07-18 11:28 |
1 |
by kinzma Mon, 2022-07-18 12:46 |
General discussion |
Pages
