You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
trying to get torque with speed (flipsky 75100) by Trecit0n on Fri, 2025-08-01 21:19 |
4 |
by Trecit0n Tue, 2025-08-12 00:05 |
General discussion | |
|
flatten the curve / powerband by TONY61 on Sun, 2025-08-10 15:26 |
by TONY61 Sun, 2025-08-10 15:26 |
General discussion | ||
|
how connect bluetooth module nRF52832 ? by netev on Mon, 2022-09-19 18:11 |
4 |
by TPEHAK Mon, 2025-08-04 06:26 |
General discussion | |
|
Sleep mode? by pcace on Wed, 2025-07-30 06:48 |
by pcace Wed, 2025-07-30 06:48 |
General discussion | ||
|
Motor runs heavy in one direction, light in the other / No speed in realtime interface / Correct phase & hall wiring? by pcace on Sat, 2025-07-26 08:00 |
by pcace Sat, 2025-07-26 08:00 |
General discussion | ||
|
How to Create Resistance Using a BLDC Motor for a Stationary Bike Conversion? by Prayoga on Tue, 2025-07-01 01:23 |
5 |
by Prayoga Mon, 2025-07-21 14:58 |
General discussion | |
|
Kaabo mantis 10 elite(minimotors) FLIPSJY 75100 DUAL ALU PCB by Musik117 on Fri, 2025-07-18 14:33 |
by Musik117 Fri, 2025-07-18 14:33 |
General discussion | ||
|
VESC Replacing Shunt Resistor with Hall Current Sensor？ by happy85 on Fri, 2025-07-18 06:21 |
by happy85 Fri, 2025-07-18 11:51 |
General discussion | ||
|
Could use some help tuning for low speed by Berrie on Tue, 2025-07-15 20:24 |
by Berrie Tue, 2025-07-15 20:24 |
General discussion | ||
|
Question about UARTs by melluh on Sun, 2021-06-13 22:50 |
2 |
by Rc 44 Fri, 2025-07-11 22:04 |
General discussion | |
|
Arduino and vesc integration issue by dsuresh on Thu, 2021-07-08 17:07 |
2 |
by Rc 44 Fri, 2025-07-11 21:57 |
General discussion | |
|
Vesc antispark always active by axelSSS on Wed, 2025-06-18 19:44 |
1 |
by tokerodev Fri, 2025-07-04 21:47 |
General discussion | |
|
Repairing by lamak on Thu, 2025-06-26 07:08 |
2 |
by ispor4en Fri, 2025-06-27 21:15 |
General discussion | |
|
eRPM limited to 40600 or so on 6.6 by Dan Slanker on Fri, 2021-04-16 01:22 |
6 |
by electricfox Wed, 2025-06-18 10:11 |
General discussion | |
|
Switch between pre-defined profiles over UART by PutridFox on Sun, 2025-06-15 13:11 |
by PutridFox Sun, 2025-06-15 13:11 |
General discussion | ||
|
Looking for VESC Tuning Help will pay $ by jordan73s on Sun, 2025-05-04 02:23 |
2 |
by colmor Thu, 2025-06-12 21:35 |
General discussion | |
|
IMU 9250 and 6050 not working on new vesc 4.12 and 4.20 by trung_qly on Sun, 2021-09-05 16:11 |
3 |
by spatsirk Mon, 2025-06-09 18:55 |
General discussion | |
|
Using the parameter editor by dqt boi on Thu, 2019-10-24 23:31 |
1 |
by Anuj Sat, 2025-06-07 16:23 |
General discussion | |
|
base on VESC6_MkVI by gavin on Wed, 2025-06-04 15:48 |
by gavin Wed, 2025-06-04 15:48 |
General discussion | ||
|
vesc tool by gavin on Wed, 2025-06-04 15:30 |
1 |
by gavin Wed, 2025-06-04 15:31 |
General discussion |
Pages
