You are here
VESC Original Hardware
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
No power or Comm via USB by swedan » Fri, 2021-04-09 14:33 |
1 |
by vadicus Fri, 2021-04-09 19:52 |
|
builtin ble on vesc 75_300 by alexefoil » Wed, 2019-07-03 02:35 |
6 |
by Glennisoty Thu, 2021-04-15 05:31 |
|
corupted firmware by Johnnylamouette » Fri, 2021-04-16 05:53 |
0 |
by Johnnylamouette Fri, 2021-04-16 06:31 |
|
HD60 CAN Resistor by BEWA » Wed, 2021-04-21 14:56 |
0 |
by BEWA Wed, 2021-04-21 14:56 |
|
VESC 75/300 ABS_OVER_CURRENT by tecnico.solarboat » Mon, 2021-04-12 21:29 |
7 |
by Gerhard Thu, 2021-05-06 18:06 |
|
VESC 75 300 R2 - correct battery conection by SafrdA » Fri, 2021-04-30 13:13 |
2 |
by frank Wed, 2021-05-26 11:19 |
|
Charging through phase wires by jesusc » Mon, 2021-01-18 21:14 |
2 |
by jesusc Thu, 2021-06-03 02:17 |
|
Built in BLE HD60 not Working by CS » Mon, 2021-08-23 13:21 |
3 |
by frank Thu, 2021-08-26 08:09 |
|
Vesc repair guidances by Booya » Tue, 2020-03-10 17:31 |
3 |
by oschlueter Fri, 2021-09-10 12:10 |
|
VESC 75/250 v 75/300? by AliBarrett10 » Tue, 2021-07-06 19:50 |
2 |
by Ht Tue, 2021-10-12 07:08 |
|
BLDC control in FOC mode by da_rul0r » Fri, 2019-08-16 15:32 |
2 |
by sanketh1691 Fri, 2021-11-05 19:05 |
|
100V vesc by paolowu64 » Tue, 2021-11-09 01:43 |
7 |
by vreppeto Mon, 2021-12-06 23:28 |
|
When 100250 is not enough by eptv » Sat, 2021-12-11 14:38 |
10 |
by eptv Wed, 2021-12-15 20:53 |
|
CAN Commands to control VESC 100/250? by harmander_sihra » Fri, 2021-12-17 01:49 |
1 |
by tecnico.solarboat Mon, 2021-12-27 23:29 |
|
3.3v short. is repair possible? by TZTZ » Sat, 2021-08-21 10:33 |
4 |
by tecnico.solarboat Mon, 2021-12-27 23:31 |
|
Getting RPM data from VESC 4.12 by EmirDns » Wed, 2022-01-05 21:20 |
0 |
by EmirDns Wed, 2022-01-05 21:20 |
|
Are the FOC PID values for discrete or continuous time controllers? by ward » Fri, 2022-01-21 15:55 |
4 |
by Elwin Tue, 2022-01-25 07:48 |
|
AS5047 with VESC75/300 by hpb66 » Mon, 2021-11-29 10:11 |
5 |
by canoeman Fri, 2022-01-28 20:17 |
|
VESC6 MK5 CAN communication does not work by Andy Moon » Tue, 2022-02-08 01:59 |
0 |
by Andy Moon Tue, 2022-02-08 01:59 |
|
FSESC 6.6 dual short on 3.3v on 1 side by vic1234 » Thu, 2022-02-17 22:33 |
4 |
by vic1234 Fri, 2022-02-18 17:52 |
|
VCC-GND short by caliber interconnect » Sat, 2022-02-26 13:10 |
4 |
by caliber interconnect Tue, 2022-03-01 10:42 |
|
Axial Flux motor control mode by ardillolambo » Wed, 2022-03-02 13:59 |
4 |
by ardillolambo Wed, 2022-03-02 18:25 |
|
Increasing phase amps beyond 300a on 100-250 by reubarb.scons » Tue, 2022-03-15 07:30 |
4 |
by reubarb.scons Thu, 2022-03-17 22:28 |
|
VESC6 Issues: Battery current inaccurate, positive ramp time, motor current max. by ESCam » Thu, 2019-03-21 22:50 |
4 |
by sp3swj Sat, 2022-03-19 15:07 |
|
Danger to go more than 100% duty cycle during downhill ? by f.damien12 » Thu, 2022-03-24 14:12 |
3 |
by skyline1970 Sat, 2022-03-26 09:29 |
Log in to post new content in the forum.