You are here
VESC Original Hardware
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Hub motor e-bike not recognized by olivierskypullc... » Tue, 2019-04-16 11:06 |
3 |
by Ampit Fri, 2023-09-29 12:38 |
|
|
How to wire MPU-9250 9DoF using SPI to vesc 6 mk4 by zmei116 » Fri, 2020-08-28 12:17 |
6 |
by TheFallen Mon, 2020-12-28 06:22 |
|
|
How to wire Cruise Control with VESC6 ADC by Tilman Baumann » Tue, 2018-04-10 11:11 |
0 |
by Tilman Baumann Tue, 2018-04-10 11:11 |
|
|
How to RC segway Ninebot pro using BALANCE mode? $$ by zmei116 » Sun, 2020-02-23 12:22 |
3 |
by zmei116 Fri, 2020-12-04 00:36 |
|
|
How to communication with arduino on vesc via can by yuri12 » Tue, 2022-02-08 13:34 |
2 |
by Craig_Gault Mon, 2023-02-27 13:20 |
|
|
How exactly do I connect a VESC 6.4 to an Arduino Nano? by MaxMaker1 » Tue, 2018-07-03 23:18 |
5 |
by molak Tue, 2019-06-04 19:39 |
|
|
Hooking up two or more motor drivers to the same MCU by darkclaude » Thu, 2019-06-20 10:02 |
2 |
by skyline1970 Wed, 2019-07-31 13:53 |
|
|
Higher voltage DRV error by jarrow » Tue, 2018-03-06 10:06 |
0 |
by jarrow Tue, 2018-03-06 10:06 |
|
|
HD60 CAN Resistor by BEWA » Wed, 2021-04-21 14:56 |
0 |
by BEWA Wed, 2021-04-21 14:56 |
|
|
HARDWARE QUESTION: Maximum AC voltage VESC can tolerate? by danvel » Fri, 2018-04-27 15:31 |
4 |
by Roger Wolff Mon, 2018-05-14 22:13 |
|
|
Hall sensor not working by Stupidspencer » Sat, 2019-12-28 20:29 |
4 |
by BeliaEllet Wed, 2021-03-31 17:55 |
|
|
Hall count drift by xachmo » Mon, 2018-03-26 07:17 |
2 |
by xachmo Wed, 2018-03-28 21:26 |
|
|
Ground Housing VESC by T18m26 » Mon, 2023-04-17 16:25 |
2 |
by T18m26 Thu, 2023-04-27 08:28 |
|
|
Getting RPM data from VESC 4.12 by EmirDns » Wed, 2022-01-05 21:20 |
0 |
by EmirDns Wed, 2022-01-05 21:20 |
|
|
FSESC 6.6 dual short on 3.3v on 1 side by vic1234 » Thu, 2022-02-17 22:33 |
4 |
by vic1234 Fri, 2022-02-18 17:52 |
|
|
Flipsky 75200 Pro suddenly stops working by terente » Thu, 2023-12-28 20:53 |
1 |
by elektrobekaniq Sat, 2024-08-03 11:44 |
|
|
Flashing via SWD works, but no green LED or USB enumeration by vpl » Fri, 2018-11-16 17:48 |
1 |
by vpl Wed, 2018-11-21 17:27 |
|
|
fault_code_high_offset_current_sensor_1 by Enak » Thu, 2019-10-10 02:48 |
2 |
by Enak Fri, 2019-10-11 01:24 |
|
|
Fault: FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 on VESC 6 by Jackl » Tue, 2019-05-28 14:48 |
0 |
by Jackl Tue, 2019-05-28 14:48 |
|
|
Dual Vesc6 setup: Vesc with nrf no blue light by Paul15578 » Sat, 2017-11-04 04:00 |
2 |
by Paul15578 Mon, 2017-11-06 13:56 |
|
|
Dual VESC sync problem by Svenska Svenson » Wed, 2017-10-18 18:56 |
4 |
by Svenska Svenson Sat, 2017-10-28 13:47 |
|
|
dual VESC battery current by chris_winkel » Tue, 2019-06-18 15:26 |
0 |
by chris_winkel Tue, 2019-06-18 15:26 |
|
|
DRV8302 Gate drive limitations by nickw1881 » Sun, 2018-04-29 09:56 |
0 |
by nickw1881 Sun, 2018-04-29 09:56 |
|
|
Driving two motors with 75/300 by cmarc » Wed, 2019-10-16 17:32 |
1 |
by benjamin Fri, 2019-10-18 10:37 |
|
|
Doubts on ERPM limit on VESC 4.12 HW by raghuvir » Tue, 2025-07-08 13:10 |
0 |
by raghuvir Tue, 2025-07-08 13:10 |
Log in to post new content in the forum.
