You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
mcpwm_set_current VS mcpwm_set_brake_current by stiganielsen » Wed, 2019-09-11 15:40 |
2 |
by mechhead Mon, 2022-02-14 11:04 |
|
|
200kHz PWM by c10yas » Sun, 2019-09-22 17:06 |
2 |
by Eric Thu, 2019-11-07 18:09 |
|
|
Driving Synchronous reluctance motor using VESC by mmandar90 » Fri, 2023-04-21 14:34 |
2 |
by Ganzey Thu, 2023-04-27 00:17 |
|
|
vesc disconnected during detection by TonyYuan » Mon, 2023-06-26 09:17 |
2 |
by powerpedalph Thu, 2025-04-24 07:51 |
|
|
VESC FOC in Encoder Mode Unstable at High eRPM by bayetan » Sun, 2023-10-08 22:40 |
2 |
by bayetan Mon, 2023-10-09 16:20 |
|
|
bootloader and firmware update for vesc 4.12 by enjoae » Thu, 2025-05-22 19:17 |
2 |
by tobydraper Sun, 2025-06-15 22:22 |
|
|
FEATURE REQUEST - ADC Mapping selection by Pimousse » Thu, 2018-09-13 09:44 |
2 |
by hackish Sun, 2019-12-08 03:53 |
|
|
VESC6 runs at 100% throttle, but then current sense is broken by nickw1881 » Mon, 2018-09-24 06:41 |
2 |
by moto_guy Thu, 2019-03-28 06:40 |
|
|
Twisted pair for Can Bus link cable? by Kenny-san650 » Tue, 2018-02-13 08:35 |
2 |
by Kenny-san650 Mon, 2018-02-19 09:15 |
|
|
Priority of CAN messages? by hmijail » Sat, 2018-10-27 06:30 |
2 |
by hmijail Fri, 2018-11-23 01:44 |
|
|
Firmware 3.37 too old, unable to Connect VESC_Tool by Nico Isn » Wed, 2018-04-18 11:17 |
2 |
by Nico Isn Fri, 2018-04-20 16:31 |
|
|
LM61 temperature sensor by ka_ru » Tue, 2020-10-13 11:55 |
2 |
by ka_ru Wed, 2020-10-14 17:33 |
|
|
Unbricking a bricked VESC6 - A step by step procedure by espen.oland » Tue, 2020-11-17 18:00 |
2 |
by h1989 Wed, 2024-11-06 06:42 |
|
|
FW stability by NATUITION » Fri, 2021-06-04 15:35 |
2 |
by berryarreo Wed, 2021-06-30 09:15 |
|
|
VESC 75300 R2 R3 , latest FW ? by E-Toxx » Sat, 2020-12-12 19:36 |
2 |
by shelbyflint Mon, 2021-04-05 09:49 |
|
|
Control System of VESC by mm_iem » Wed, 2021-08-25 14:52 |
2 |
by kubark42 Wed, 2021-11-17 16:59 |
|
|
VESC 100-250 doesn't work with firmware built from 100_250 folder by aerostepa » Sat, 2021-01-30 17:14 |
2 |
by aerostepa Sun, 2021-01-31 17:42 |
|
|
VESC4 phase shunt by Rico » Tue, 2019-05-21 16:09 |
3 |
by svs Thu, 2019-08-08 08:41 |
|
|
I put the wrong firmware (48) on my 4.12 vesc from Hobbyking by drawliphant » Mon, 2019-01-14 22:09 |
3 |
by drawliphant Wed, 2019-01-16 08:19 |
|
|
High Power Configuration with Resolver Feedback by Acable » Sat, 2019-03-23 19:28 |
3 |
by paltatech Wed, 2019-04-03 12:57 |
|
|
VESC 4.12 firmware 3.38 flash back to firmware 2.18 by Arm007 » Thu, 2019-04-11 08:30 |
3 |
by skyline1970 Fri, 2019-08-02 15:15 |
|
|
SPI Encoder communications with AS5047 by vadimz » Sun, 2018-10-28 16:55 |
3 |
by Guillaume227 Mon, 2019-02-11 23:14 |
|
|
position hold below specific duty cycle by lacondro » Wed, 2022-04-27 04:41 |
3 |
by Matevz Tue, 2025-11-18 14:17 |
|
|
General Question about firmware and software by Dor_Segev » Sat, 2020-03-21 13:59 |
3 |
by Dor_Segev Tue, 2020-03-24 09:32 |
|
|
What is the recommended way to implement a new encoder in the VESC firmware? by toma » Mon, 2019-11-04 00:19 |
3 |
by James Donker Mon, 2025-01-27 18:53 |
Log in to post new content in the forum.
