You are here

VESC Tool

Topic / Topic startersort descending Replies Last post
Normal topic Hall sensor data is all 0. What do?
by Byproduct » Sat, 2023-01-14 14:39
0
by Byproduct
Sat, 2023-01-14 17:45
Normal topic Hall sensor problems
by Traceo » Wed, 2021-11-10 00:05
2
by Traceo
Fri, 2021-11-19 22:35
Normal topic Help i can not setup my motors
by jakson01 » Fri, 2022-09-09 18:37
0
by jakson01
Fri, 2022-09-09 18:37
Normal topic Help needed for VESC set up!
by mbagrey » Wed, 2018-09-19 22:07
3
by Roger Wolff
Sun, 2018-09-30 16:15
Normal topic Help setting up dual vesc via CANBUS
by Jaystro16 » Sun, 2019-08-04 01:39
1
by frank
Wed, 2019-08-14 13:55
Normal topic Help with a settings for only generator
by Mafo » Fri, 2018-03-02 16:59
6
by Mafo
Thu, 2018-03-15 11:15
Normal topic help with vesc real time data trouble shooting
by stefann » Wed, 2020-04-08 23:03
0
by stefann
Wed, 2020-04-08 23:03
Normal topic help with vesc real time data trouble shooting
by stefann » Wed, 2020-04-08 23:02
0
by stefann
Wed, 2020-04-08 23:02
Normal topic HFI plot
by Rick van der Sloot » Sun, 2022-10-02 22:26
0
by Rick van der Sloot
Sun, 2022-10-02 22:26
Normal topic High Current Sampling Mode True 80% current
by antonchromjak » Sun, 2017-09-24 21:14
2
by antonchromjak
Wed, 2017-09-27 19:59
Normal topic Hoverboard motor Reverse direction
by Silvio Semedo » Sat, 2021-01-16 17:43
1
by skyline1970
Sun, 2021-02-07 17:32
Normal topic Hoverboard Motor Setup
by CadillacF1 » Sat, 2020-07-11 05:26
2
by TheFallen
Mon, 2020-08-17 12:14
Normal topic How Can I make the tool work with FW 3.5 instead of just 3.58?
by ipbyrne » Fri, 2019-07-26 18:20
3
by frank
Wed, 2019-08-14 14:01
Hot topic How can we log all the real time data like motor current, battery current,etc to analyze them later?
by vimi94 » Thu, 2019-05-02 09:57
24
by ahagge
Thu, 2021-09-09 05:05
Normal topic How do I compile the VESC Tool?
by ipbyrne » Wed, 2019-07-24 16:58
4
by a.dahhak
Fri, 2021-01-01 15:25
Normal topic How do I disable brake?
by moo10032 » Tue, 2021-02-23 08:09
0
by moo10032
Tue, 2021-02-23 08:10
Normal topic How to access VESC error codes in the new VESC tool
by berno3 » Tue, 2018-06-05 08:47
1
by Roger Wolff
Wed, 2018-06-06 07:36
Normal topic how to communication with arduino on vesc via CAN
by yuri12 » Tue, 2022-02-08 13:16
0
by yuri12
Tue, 2022-02-08 13:16
Normal topic How to control motor using VESC tool in computer at constant rpm?
by vimi94 » Wed, 2019-05-01 12:56
3
by foreclosurecat
Tue, 2022-12-06 22:36
Normal topic How to determine motor size in wizard, hub motors ?
by Photolad61 » Mon, 2019-03-25 19:43
1
by Kent Tabor
Fri, 2020-10-23 22:29
Normal topic How to Enable kill switch support in Firmware 5.03
by iserai2r » Sat, 2022-02-05 13:59
4
by moose09876
Tue, 2022-07-26 22:29
Normal topic How to get vesc tool for linux on ubuntu?
by vitormhenrique » Tue, 2019-10-22 16:00
6
by sanketh1691
Thu, 2021-09-30 05:05
Normal topic How to increase startup torque?
by Enak » Fri, 2017-09-08 01:14
4
by vadicus
Tue, 2021-02-23 19:44
Normal topic How to keep motor at 0RPM
by zapshe » Thu, 2022-09-08 13:51
2
by harringtongrimes
Wed, 2022-09-21 11:06
Normal topic How to read COMM_ROTOR_POSITION through uart
by Graham Bowen-Davies » Wed, 2021-04-28 23:59
2
by Gloobox
Wed, 2022-11-30 18:39
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - VESC Tool