You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Motor not running after applying SINE/COSINE settings by DHOUT » Fri, 2023-01-27 03:32 |
0 |
by DHOUT Fri, 2023-01-27 03:32 |
|
|
Flipsky 75100foc motor detection sensor issue fails every crysaltemotor I've tried by Wheelzscootersinc » Fri, 2023-02-03 21:36 |
1 |
by tom355 Sun, 2023-02-05 11:11 |
|
|
duty cicle 95% but current not at max by rodrigo.baronio » Mon, 2023-02-06 15:52 |
0 |
by rodrigo.baronio Mon, 2023-02-06 15:52 |
|
|
Noobs need to update and / or configure old VESC 4.12 by Loops » Tue, 2023-02-07 11:49 |
0 |
by Loops Tue, 2023-02-07 11:49 |
|
|
Hall sensor data is all 0. What do? by Byproduct » Sat, 2023-01-14 14:39 |
0 |
by Byproduct Wed, 2023-02-08 11:21 |
|
|
Installing VESC Tool on Jetson Nano by mrburns19 » Tue, 2023-02-07 04:54 |
2 |
by mrburns19 Sun, 2023-02-12 01:44 |
|
|
VESC Tool Control Theory by AeonCypher » Sun, 2023-02-12 23:54 |
0 |
by AeonCypher Sun, 2023-02-12 23:54 |
|
|
How to Enable kill switch support in Firmware 5.03 by iserai2r » Sat, 2022-02-05 13:59 |
5 |
by rodrigo.baronio Tue, 2023-02-14 02:27 |
|
|
Detection failed. Reason: Sensor detection failed by Lilian_CASTEL » Tue, 2020-11-24 11:31 |
8 |
by electricfox Thu, 2023-02-16 15:57 |
|
|
Data logging for dual VESC on Android VESC-tool by elmardus » Wed, 2021-10-20 16:13 |
5 |
by SamuL Fri, 2023-02-17 00:55 |
|
|
Throttle movement by Lasse » Tue, 2023-03-07 12:16 |
0 |
by Lasse Tue, 2023-03-07 12:16 |
|
|
VESC Tool crashes when loading/saving motor/app config by bkyrevolution » Thu, 2023-03-02 20:27 |
1 |
by jimtzer Mon, 2023-03-13 00:30 |
|
|
Acceleration ramping using UART communication with arduino on VTool 6.0 by Kokonenen » Tue, 2023-04-04 11:48 |
1 |
by Kokonenen Tue, 2023-04-04 14:30 |
|
|
Position control without encoder by bearing » Tue, 2023-04-04 18:45 |
1 |
by bearing Thu, 2023-04-06 22:07 |
|
|
How to adjust ADC1 parameters to adjust the speed (not working) by player107 » Fri, 2023-04-14 13:46 |
0 |
by player107 Fri, 2023-04-14 13:46 |
|
|
Can't get Dual drive/CAN bus working by Xadiant » Sun, 2019-09-22 20:49 |
11 |
by Kokonenen Wed, 2023-04-19 11:10 |
|
|
Parameters for efoil by vladek » Thu, 2023-04-20 12:54 |
0 |
by vladek Thu, 2023-04-20 12:54 |
|
|
RT Data Logging by adas29 » Wed, 2023-04-26 22:59 |
0 |
by adas29 Wed, 2023-04-26 22:59 |
|
|
Sailboat regen by flydr2 » Wed, 2023-04-12 20:10 |
1 |
by vadicus Wed, 2023-05-10 20:06 |
|
|
How to log events on a non bluetooth onewheel setup by carasta » Sat, 2023-05-13 22:01 |
0 |
by carasta Sat, 2023-05-13 22:01 |
|
|
"Allow Breaking" set to "TRUE" when "Backup COnfigurations (Including CAN) by bayetan » Mon, 2023-05-22 05:33 |
0 |
by bayetan Mon, 2023-05-22 05:33 |
|
|
Connect VESC4.7 over USB by Lars_Dierickx » Thu, 2023-03-09 16:13 |
1 |
by Jou2023 Mon, 2023-05-29 11:13 |
|
|
Comm conflict when connecting external imu? by Lennart Duijn » Wed, 2023-05-31 22:53 |
0 |
by Lennart Duijn Wed, 2023-05-31 22:53 |
|
|
Issue with Vesc Tool: MPU6050 IMU Not Detected After Power Cycling by Lennart Duijn » Thu, 2023-06-01 21:54 |
0 |
by Lennart Duijn Fri, 2023-06-02 09:03 |
|
|
Not sure if parameter update in VESC tool works by srinath » Thu, 2023-06-08 11:29 |
0 |
by srinath Thu, 2023-06-08 11:29 |
Log in to post new content in the forum.
