You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Motor temperature, how to set limit >120 C ? by RSR » Wed, 2018-08-22 12:40 |
3 |
by Danny Bokma Thu, 2018-08-23 07:19 |
|
|
Motor Stuck at 55% Duty Cycle by motion_sickness » Sun, 2021-11-14 16:47 |
1 |
by drdrs Sun, 2021-11-14 21:20 |
|
|
motor stops spinning on its own by rsarver » Tue, 2021-03-16 16:30 |
1 |
by rsarver Tue, 2021-03-16 22:13 |
|
|
Motor starting while flasing firmware by RSR » Sun, 2017-09-17 15:31 |
0 |
by RSR Sun, 2017-09-17 15:31 |
|
|
Motor setup help please by TrevM » Wed, 2017-12-13 17:11 |
2 |
by nickw1881 Wed, 2018-03-21 05:42 |
|
|
Motor RPM counter in Dashboard and Mob App by Rex » Fri, 2022-06-17 07:01 |
0 |
by Rex Fri, 2022-06-17 07:01 |
|
|
Motor Poles by Enak » Fri, 2017-09-08 00:57 |
1 |
by ThierryGTLTS Fri, 2017-09-08 09:01 |
|
|
Motor not Spinning Up During Setup Wizard by superjay » Tue, 2021-11-23 07:03 |
4 |
by superjay Wed, 2021-11-24 11:25 |
|
|
Motor not running after applying SINE/COSINE settings by DHOUT » Fri, 2023-01-27 03:32 |
0 |
by DHOUT Fri, 2023-01-27 03:32 |
|
|
motor max rpm and current severely limited? by Roy Zhang » Mon, 2021-08-09 19:23 |
2 |
by vadicus Thu, 2021-08-12 04:06 |
|
|
Motor FOC Config Wizard only sees "local" motor, not CAN connected by glasswalker » Mon, 2024-04-08 04:46 |
1 |
by glasswalker Mon, 2024-04-08 23:33 |
|
|
motor experiment does nothing by greaterebiz » Mon, 2022-04-11 18:27 |
3 |
by swinckler Fri, 2022-07-01 14:38 |
|
|
Motor detection failed/ 0 faults by jnweb29 » Sat, 2017-12-23 21:07 |
0 |
by jnweb29 Sat, 2017-12-23 21:07 |
|
|
motor detection - what to expect when spinning up the motor by grantmoy74 » Sat, 2019-12-28 11:58 |
2 |
by grantmoy74 Sun, 2019-12-29 05:21 |
|
|
Motor control by ptss37 » Wed, 2021-12-08 06:52 |
5 |
by ptss37 Fri, 2021-12-10 03:24 |
|
|
Motor command in log? by carboninfusion » Tue, 2020-08-04 07:58 |
0 |
by carboninfusion Tue, 2020-08-04 07:59 |
|
|
Motor clicking and not spinning after setup wizard by dfelz » Fri, 2020-04-03 03:51 |
6 |
by brian adilman Wed, 2022-01-26 13:36 |
|
|
Motor and input calibration without drive train by technique » Tue, 2020-07-14 19:22 |
0 |
by technique Tue, 2020-07-14 19:22 |
|
|
Motor always accelerates to maximum speed by zapshe » Sun, 2022-09-11 03:46 |
1 |
by skyline1970 Sun, 2022-11-27 16:32 |
|
|
More detail in tool tips by TechAUmNu » Mon, 2018-07-23 20:15 |
2 |
by TechAUmNu Tue, 2018-07-24 13:52 |
|
|
Missing Braking Power in ADC by Silverline » Wed, 2019-06-12 19:48 |
8 |
by positiv Fri, 2020-01-24 14:07 |
|
|
Minimum System Requirements for VESC Tool 3.01 under Windows by j.konrad » Mon, 2022-01-24 21:48 |
0 |
by j.konrad Mon, 2022-01-24 21:48 |
|
|
Maxkgo bms configuration inside vesc tool by renaudbarbier » Fri, 2024-04-19 15:53 |
0 |
by renaudbarbier Fri, 2024-04-19 15:53 |
|
|
Maximum possible Baudrate in UART? by nlabs » Sun, 2018-04-08 01:52 |
5 |
by anttok Tue, 2020-12-01 00:26 |
|
|
Maximum Duty Cycle limit is 95% by shimdidly » Sun, 2017-10-01 19:59 |
4 |
by shimdidly Sat, 2017-10-07 01:42 |
Log in to post new content in the forum.
