You are here

VESC Tool

Topic / Topic starter Replies Last postsort ascending
Normal topic ADC throttle is accelerating th full throttle quickly
by Buddah » Sun, 2019-09-15 23:32
4
by jimtzer
Wed, 2021-06-30 17:54
Normal topic Use Vesc-Tool to run two motors simultaneously via CAN
by microlomaniac » Thu, 2021-06-17 11:55
2
by spacewalker
Tue, 2021-06-22 08:23
Normal topic Startup codes?
by anthonys » Sat, 2021-06-19 17:29
0
by anthonys
Sat, 2021-06-19 17:29
Normal topic Motor whine with HFI?
by christopher.h.poole » Mon, 2021-04-19 15:49
2
by christopher.h.poole
Tue, 2021-06-15 21:18
Normal topic NRF5X SWD Prog detection broken, always detects NRF52832 512K/64K
by zippy » Sun, 2021-06-06 16:19
1
by zippy
Sun, 2021-06-06 17:58
Normal topic FOC configuration - Motor stalls during measurement
by Lukinio » Wed, 2021-05-26 12:31
1
by Lukinio
Wed, 2021-05-26 12:44
Normal topic APP settings for Motor Position and RPM control with PPM
by Marcos Bleda » Fri, 2021-05-21 10:47
0
by Marcos Bleda
Fri, 2021-05-21 10:47
Normal topic Update FW on multiple VESC pcbs using CAN issue
by Offline » Thu, 2021-05-20 07:36
0
by Offline
Thu, 2021-05-20 07:36
Normal topic read RPM over CAN
by nblange » Mon, 2021-05-03 20:43
0
by nblange
Mon, 2021-05-03 20:43
Normal topic Problem with VESC Tool vs BLDC FW version
by Reidar Jortveit » Mon, 2021-04-26 14:39
1
by Reidar Jortveit
Mon, 2021-04-26 14:49
Normal topic no effect on set erpm/speed limit
by xenon321 » Sat, 2021-04-24 20:43
0
by xenon321
Sun, 2021-04-25 16:53
Normal topic DC Motor Settings (24v PowerWheels)
by KirkusMaximus » Thu, 2021-04-22 00:17
0
by KirkusMaximus
Thu, 2021-04-22 00:18
Normal topic two motors one ppm for throttle and one for the direction?
by Robby Ertmann » Wed, 2021-04-21 13:48
0
by Robby Ertmann
Wed, 2021-04-21 13:48
Normal topic throttle mapping: non-zero current at zero adc input?
by FreddyForLaunch » Wed, 2021-04-14 21:48
0
by FreddyForLaunch
Thu, 2021-04-15 09:00
Normal topic Pc requirement to run vesc software
by proget.snc » Mon, 2021-04-12 10:57
1
by benjamin
Wed, 2021-04-14 19:47
Normal topic Questions on VESC tool
by da_rul0r » Wed, 2019-08-14 09:47
5
by Isi
Mon, 2021-04-12 17:34
Normal topic Get data from VESC on Arduino
by jhanvisharma » Wed, 2021-04-07 08:25
1
by CTSchorsch
Wed, 2021-04-07 09:05
Normal topic VESC failure presumably due to current oscillations at high current
by rsarver » Wed, 2021-03-24 22:06
0
by rsarver
Wed, 2021-03-24 22:06
Normal topic Full Brake vs Switch Off
by meisterpro » Mon, 2021-03-22 14:36
0
by meisterpro
Mon, 2021-03-22 14:36
Normal topic Data logging
by charper » Wed, 2019-05-22 00:48
4
by StvMan
Sun, 2021-03-21 17:20
Normal topic D vs omega control
by rsarver » Wed, 2021-03-17 14:44
0
by rsarver
Wed, 2021-03-17 14:44
Normal topic motor stops spinning on its own
by rsarver » Tue, 2021-03-16 16:30
1
by rsarver
Tue, 2021-03-16 22:13
Normal topic Battery Voltage Settings
by huffauden19 » Wed, 2020-03-04 23:17
2
by laser30
Sat, 2021-03-13 16:57
Normal topic Update fail from FW3.58 to 3.61
by sachs2019 » Tue, 2019-09-10 15:51
7
by AlmaRaposa
Thu, 2021-03-11 17:44
Normal topic I Mac Vesc tool !!!!
by PHATTY » Fri, 2019-10-11 17:56
2
by Bender
Wed, 2021-03-10 14:39
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - VESC Tool