You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC tool and sk8-esc V6 set up shows incorrectcurrent usage by DominykasS » Fri, 2022-09-30 13:54 |
2 |
by Frizzaper Wed, 2023-11-15 04:25 |
|
|
Firmware issues by salvasalce » Tue, 2022-12-13 16:12 |
2 |
by Lennart Duijn Mon, 2023-01-09 22:10 |
|
|
[SOLVED] RPM setting not working by olivierskypullc... » Wed, 2019-02-27 12:14 |
2 |
by olivierskypullc... Wed, 2019-03-06 10:10 |
|
|
Vesc Tool not opening on windows computer by maccert » Sat, 2019-03-02 11:04 |
2 |
by Luca Torani Sun, 2019-03-03 20:32 |
|
|
Is it possible to stop a motor at one exact desired location without hall sensor? by vimi94 » Thu, 2019-08-15 10:58 |
2 |
by vimi94 Tue, 2019-08-20 13:37 |
|
|
BEMF plot not working with VESC6 by ESCam » Tue, 2019-03-12 21:29 |
2 |
by ESCam Tue, 2019-03-19 18:03 |
|
|
How to Traction Control VESC 6 by Karl » Thu, 2018-10-11 03:33 |
2 |
by marti Wed, 2018-10-17 06:02 |
|
|
Voltage measurement calibration? by pyryjansson » Tue, 2019-04-30 20:19 |
2 |
by frank Wed, 2022-11-30 09:55 |
|
|
load cell data logging by magnus.w » Thu, 2019-05-02 00:21 |
2 |
by Tom Burton Wed, 2019-11-06 16:43 |
|
|
Wrong HW version selected during FW update by babyboi » Sat, 2018-12-15 21:30 |
2 |
by babyboi Sat, 2018-12-22 03:55 |
|
|
Motor whine with HFI? by christopher.h.poole » Mon, 2021-04-19 15:49 |
2 |
by christopher.h.poole Tue, 2021-06-15 21:18 |
|
|
Connect VESC to Keyboard/Wireless Joystick by sanketh1691 » Mon, 2021-10-04 20:58 |
2 |
by sanketh1691 Wed, 2021-10-06 18:58 |
|
|
VESC TOOL cant connect to hardware by svs » Sat, 2021-04-24 22:06 |
2 |
by jose carceller Sun, 2022-08-21 00:43 |
|
|
motor to slow and no power by Thiery Vardon » Sat, 2021-01-09 10:45 |
2 |
by Thiery Vardon Tue, 2021-01-12 13:27 |
|
|
VESCTOOL - Multiple VESC simultaneous configuration (Same CANBUS ID issues) by Filcas » Thu, 2021-02-18 20:52 |
2 |
by Filcas Fri, 2021-02-19 01:37 |
|
|
Use Vesc-Tool to run two motors simultaneously via CAN by microlomaniac » Thu, 2021-06-17 11:55 |
2 |
by spacewalker Tue, 2021-06-22 08:23 |
|
|
Software safety features interrupting normal operation. by Tsomo » Wed, 2021-07-14 01:29 |
2 |
by Tsomo Wed, 2021-07-14 01:32 |
|
|
current control via CAN not working by STTS » Thu, 2021-08-12 11:51 |
2 |
by mm_iem Mon, 2021-08-30 18:00 |
|
|
Question about FOC Wizard by proget.snc » Thu, 2021-08-26 16:31 |
2 |
by proget.snc Thu, 2021-09-02 14:23 |
|
|
[Solved] VESC Tool "could not deserialize motor configuration" with custom firmware by bsobeloffgittes » Fri, 2024-05-03 20:30 |
2 |
by rafeh1 Wed, 2024-11-06 09:14 |
|
|
VESC runs only with 50% duty cycle by Nimrod0201 » Wed, 2024-07-10 18:30 |
2 |
by Nimrod0201 Sat, 2024-07-13 11:34 |
|
|
brake switch/brake regen question by smallbikefun » Sat, 2024-04-06 01:48 |
2 |
by smallbikefun Sun, 2024-04-14 22:08 |
|
|
BUG - RAMPING on VESC TOOL? by Filcas » Tue, 2019-12-10 19:29 |
2 |
by Filcas Wed, 2019-12-11 17:15 |
|
|
Vesc tool 1.26.. issue with firmware updates? by beetbocks » Tue, 2019-12-17 10:17 |
2 |
by Stupidspencer Wed, 2019-12-25 23:04 |
|
|
motor detection - what to expect when spinning up the motor by grantmoy74 » Sat, 2019-12-28 11:58 |
2 |
by grantmoy74 Sun, 2019-12-29 05:21 |
Log in to post new content in the forum.
