You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
PPM Pulselength mapping by Shaftdriver » Tue, 2022-10-04 17:18 |
0 |
by Shaftdriver Tue, 2022-10-04 17:18 |
|
|
TWO MOTOR SYSTEM by ronmotor » Mon, 2022-10-17 00:44 |
0 |
by ronmotor Mon, 2022-10-17 00:44 |
|
|
Vesc efficiency through log (.CSV) by th0masrtg » Tue, 2022-11-22 10:08 |
0 |
by th0masrtg Tue, 2022-11-22 10:08 |
|
|
Connection over USB failed by sangious » Sun, 2019-03-17 01:20 |
0 |
by sangious Sun, 2019-03-17 01:20 |
|
|
Older version of VESC Tool by Gas_Sn4ke » Fri, 2018-11-30 09:28 |
0 |
by Gas_Sn4ke Fri, 2018-11-30 09:28 |
|
|
UART write read arduino by matiller » Sat, 2019-06-01 20:18 |
0 |
by matiller Sat, 2019-06-01 20:18 |
|
|
Full Brake vs Switch Off by meisterpro » Mon, 2021-03-22 14:36 |
0 |
by meisterpro Mon, 2021-03-22 14:36 |
|
|
Several questions and safe values by miskuhunor@gmail.com » Thu, 2021-09-09 08:33 |
0 |
by miskuhunor@gmail.com Thu, 2021-09-09 08:33 |
|
|
PPM Mapping by russell.morris1... » Tue, 2021-09-14 22:38 |
0 |
by russell.morris1... Tue, 2021-09-14 22:38 |
|
|
throttle mapping: non-zero current at zero adc input? by FreddyForLaunch » Wed, 2021-04-14 21:48 |
0 |
by FreddyForLaunch Thu, 2021-04-15 09:00 |
|
|
DC Motor Settings (24v PowerWheels) by KirkusMaximus » Thu, 2021-04-22 00:17 |
0 |
by KirkusMaximus Thu, 2021-04-22 00:18 |
|
|
APP settings for Motor Position and RPM control with PPM by Marcos Bleda » Fri, 2021-05-21 10:47 |
0 |
by Marcos Bleda Fri, 2021-05-21 10:47 |
|
|
Incorrect speed too high by Michele84 » Wed, 2021-07-21 15:48 |
0 |
by Michele84 Wed, 2021-07-21 15:48 |
|
|
Reconstruct detection control algorithm inside the tool by kaanozgen » Wed, 2020-02-26 18:50 |
0 |
by kaanozgen Wed, 2020-02-26 18:50 |
|
|
Current measurement VESC Tool 1.16 by mdbb » Thu, 2020-03-19 17:16 |
0 |
by mdbb Thu, 2020-03-19 17:16 |
|
|
DC MOTOR connected to FLIPSKY 4.20 MINI by CatalinCHIRICA » Mon, 2019-12-02 18:20 |
0 |
by CatalinCHIRICA Mon, 2019-12-02 18:20 |
|
|
Tool for OSX MAC by oger » Wed, 2020-03-25 17:21 |
0 |
by oger Wed, 2020-03-25 17:21 |
|
|
Programming VESC through CANbus adapter by Filcas » Sat, 2020-03-28 11:43 |
0 |
by Filcas Sat, 2020-03-28 11:43 |
|
|
UART Safety Feature by jaghori.sasan » Wed, 2019-09-04 18:45 |
0 |
by jaghori.sasan Wed, 2019-09-04 18:45 |
|
|
arrow key hot working (neither on the app) but the board works correclty by lorenzidomenico94 » Tue, 2020-01-14 11:30 |
0 |
by lorenzidomenico94 Tue, 2020-01-14 11:30 |
|
|
VESC tool load empty by arminoonk » Thu, 2020-01-16 14:51 |
0 |
by arminoonk Thu, 2020-01-16 14:51 |
|
|
FOC Encoder autotune issue by David_Lo » Tue, 2020-01-21 11:54 |
0 |
by David_Lo Tue, 2020-01-21 11:54 |
|
|
Input Setup Wizard - Update Firmware by pmg » Thu, 2020-02-13 09:54 |
0 |
by pmg Thu, 2020-02-13 09:54 |
|
|
ADC and arrow input dont work by stefann » Wed, 2019-10-09 18:51 |
0 |
by stefann Wed, 2019-10-09 20:04 |
|
|
The engine stopped spinning after updating firmware by brian adilman » Wed, 2022-01-26 17:40 |
0 |
by brian adilman Wed, 2022-01-26 19:15 |
Log in to post new content in the forum.
