You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 » Wed, 2023-04-12 16:28 |
0 |
by Tom65 Wed, 2023-04-12 16:28 |
|
|
current measurements crazy high after replacing DRV8301 with DRV8302, it throws a FAULT_CODE_ABS_OVER_CURRENT by idkanythinggoes » Thu, 2021-03-18 04:34 |
0 |
by idkanythinggoes Thu, 2021-03-18 04:34 |
|
|
Position Limits w/ BDC and ABI Encoder by gokulswami » Thu, 2023-04-13 10:43 |
0 |
by gokulswami Thu, 2023-04-13 10:43 |
|
|
How to set dead time on BLDC mode? by AllenFF » Wed, 2020-04-15 03:27 |
0 |
by AllenFF Wed, 2020-04-15 03:27 |
|
|
Minimum speed push cart using arduino by BarBumble » Wed, 2021-05-12 09:29 |
0 |
by BarBumble Wed, 2021-05-12 09:29 |
|
|
VESC6 cooked MOSFET by hagoston » Mon, 2021-03-22 14:23 |
0 |
by hagoston Mon, 2021-03-22 15:03 |
|
|
NRF Implementation by Christian » Thu, 2018-02-15 14:36 |
0 |
by Christian Thu, 2018-02-15 14:36 |
|
|
12v(3s) Input to VESC 75/250 by AliBarrett10 » Wed, 2021-03-24 14:36 |
0 |
by AliBarrett10 Wed, 2021-03-24 16:19 |
|
|
Bench Testing by usaevo7 » Tue, 2023-04-25 16:50 |
0 |
by usaevo7 Tue, 2023-04-25 16:50 |
|
|
Do I need a motor with Hall sensor to use Vesc tool? by greew » Sun, 2020-05-31 06:48 |
0 |
by greew Sun, 2020-05-31 06:48 |
|
|
Firmware Update = Quiet Motor? by worldmaverik » Sun, 2020-04-19 21:45 |
0 |
by worldmaverik Sun, 2020-04-19 21:45 |
|
|
120V dual VESC for E-scooter by Daniel Kaminski » Sun, 2021-03-28 12:43 |
0 |
by Daniel Kaminski Sun, 2021-03-28 12:43 |
|
|
DUAL VESC FOR BIDIRECTIONAL ROTATION by Khaliduzzaman Mredul » Fri, 2023-05-05 06:46 |
0 |
by Khaliduzzaman Mredul Fri, 2023-05-05 11:00 |
|
|
Compatibility with BiSS-C absolute encoder by wisllayvitrio » Sat, 2021-05-15 23:39 |
0 |
by wisllayvitrio Sat, 2021-05-15 23:40 |
|
|
issue by control brushed DC with VESC 4.12 by segway » Sun, 2020-04-26 16:06 |
0 |
by segway Thu, 2020-06-04 10:26 |
|
|
mxus xf15 thermistor by ligi » Tue, 2021-05-18 09:43 |
0 |
by ligi Tue, 2021-05-18 09:43 |
|
|
. by faheemift » Tue, 2021-03-30 15:37 |
0 |
by faheemift Thu, 2021-04-01 13:58 |
|
|
Duty vs RPM for smooth start and slow running by Davideo » Tue, 2018-04-24 14:42 |
0 |
by Davideo Tue, 2018-04-24 14:42 |
|
|
VESC 75100 motor detection fine but then motor won't run just shudders and resistance by Jidobaba » Sun, 2024-04-21 03:17 |
0 |
by Jidobaba Sun, 2024-04-21 03:17 |
|
|
VESC for EU pedelecs by bb67 » Mon, 2020-04-27 14:11 |
0 |
by bb67 Mon, 2020-04-27 14:13 |
|
|
BLDC zero cross happens too early by Sgw32 » Thu, 2021-05-20 19:10 |
0 |
by Sgw32 Thu, 2021-05-20 19:10 |
|
|
Newer DRV8353RS instead of DRV8301? by whydoilive » Fri, 2021-04-02 10:24 |
0 |
by whydoilive Fri, 2021-04-02 10:24 |
|
|
20S by ahanktcd » Thu, 2024-04-25 14:51 |
0 |
by ahanktcd Thu, 2024-04-25 14:51 |
|
|
Motor switch off moving on at 10°C by sirAnton » Sun, 2021-04-04 10:55 |
0 |
by sirAnton Sun, 2021-04-04 10:55 |
|
|
Interfacing with the VESC using UART by dhruvna » Thu, 2023-03-16 17:42 |
0 |
by dhruvna Thu, 2023-03-16 17:42 |
Log in to post new content in the forum.
