You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Will the new VESC company have plans related to robotics applications? by radish » Fri, 2025-09-05 13:14 |
1 |
by radish Fri, 2025-09-05 13:20 |
|
|
Will a Flipsky FSESC4.20 50A Controller Work with Unknown Motor? by Laurie Forbes » Thu, 2021-09-30 21:31 |
1 |
by andyw2005 Fri, 2021-10-22 00:09 |
|
|
Why use sensorless if the motor has sensors? by j.konrad » Thu, 2022-02-17 14:25 |
4 |
by j.konrad Mon, 2022-02-21 15:06 |
|
|
Why switchable current filters? by BillyJ » Sat, 2019-10-05 12:22 |
2 |
by shaman Sun, 2019-10-13 17:41 |
|
|
Why not using interrupt for Hall signal detection? by kuan » Sun, 2021-01-03 09:51 |
0 |
by kuan Sun, 2021-01-03 09:51 |
|
|
Why is the speed lower in FOC mode than BLDC mode ? by stone_1706 » Thu, 2019-01-17 08:23 |
8 |
by speed3r Wed, 2022-06-15 09:34 |
|
|
Why is my VESC Speed (in MPH) half what it should be? by ALarabie » Fri, 2022-12-09 17:41 |
6 |
by vadicus Sat, 2022-12-10 19:00 |
|
|
Why i cant insert a topic? by SafrdA » Thu, 2021-04-29 20:41 |
0 |
by SafrdA Thu, 2021-04-29 20:41 |
|
|
Why don't BLDCs require PFC capacitors? by batdan » Mon, 2019-09-16 17:41 |
1 |
by DarioP Sun, 2020-11-22 16:43 |
|
|
Which to believe, manufacturer inductance spec or VESC autodetection? by kubark42 » Wed, 2021-09-29 15:59 |
3 |
by kubark42 Fri, 2021-10-22 20:01 |
|
|
Which encoders are supported? by raess » Thu, 2018-03-22 23:38 |
2 |
by raess Fri, 2018-03-23 22:58 |
|
|
which configuration file I should change to make operate a VESC at 800 Volts by JCordova » Tue, 2024-02-06 17:49 |
1 |
by NOAI Wed, 2024-02-07 15:54 |
|
|
Which App to use and how to wire it by philboslaggins » Sat, 2022-11-05 16:20 |
2 |
by nando Fri, 2025-08-29 15:19 |
|
|
where to source BLDC 6.5in geared wheel? by fourchette » Thu, 2018-11-08 00:05 |
3 |
by fourchette Mon, 2018-11-19 22:54 |
|
|
Where to find CAN protocol documentation? by doctarr » Tue, 2020-12-29 15:33 |
0 |
by doctarr Tue, 2020-12-29 15:33 |
|
|
Where to connect the Button for Reverse driver?, in ADC mode (Ebike throttle) by Astropower » Sun, 2019-05-19 22:10 |
3 |
by hackish Sun, 2019-09-08 05:31 |
|
|
Where can I ask technical questions about products? by MrSurly » Tue, 2022-04-19 05:22 |
0 |
by MrSurly Tue, 2022-04-19 05:22 |
|
|
When SWD Program Connect Fails by canoeman » Mon, 2022-02-28 18:32 |
0 |
by canoeman Mon, 2022-02-28 18:32 |
|
|
when speed of vesc motor too fast and the arduino pin signal is unstable by HumorLogic » Tue, 2021-04-06 14:21 |
3 |
by woliam Sat, 2021-04-10 15:17 |
|
|
When I mount the propeller on the motor ,I get a new promblem by moto_guy » Sat, 2019-03-02 05:16 |
0 |
by moto_guy Sat, 2019-03-02 05:16 |
|
|
Wheels only rotate about a quarter of a turn by Appearance » Mon, 2021-10-04 17:57 |
2 |
by drummerboy5408 Wed, 2021-10-13 05:08 |
|
|
wheelchair with a joystick via Vesc by hopeingod » Fri, 2024-05-17 12:00 |
0 |
by hopeingod Fri, 2024-05-17 12:00 |
|
|
Wheel speed over CANBUS by paule » Tue, 2020-12-29 13:04 |
0 |
by paule Tue, 2020-12-29 13:04 |
|
|
What's wrong with my motors? by Mads7400 » Fri, 2020-05-08 15:05 |
1 |
by tylr_r Wed, 2020-07-15 01:22 |
|
|
What's the PCB dimension of the VESC 6? by darwinbeing » Fri, 2018-04-06 06:52 |
2 |
by darwinbeing Thu, 2023-08-03 21:11 |
Log in to post new content in the forum.
