You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
current measurements crazy high after replacing DRV8301 with DRV8302, it throws a FAULT_CODE_ABS_OVER_CURRENT by idkanythinggoes » Thu, 2021-03-18 04:34 |
0 |
by idkanythinggoes Thu, 2021-03-18 04:34 |
|
current proportional pwm signal by grkn5434 » Mon, 2020-02-24 11:42 |
2 |
by grkn5434 Mon, 2020-02-24 15:40 |
|
Current Sensing in VESC by Toshi Sharma » Fri, 2021-11-26 08:51 |
17 |
by Toshi Sharma Tue, 2022-01-04 11:46 |
|
Current sensor and commanded current by galp » Fri, 2019-02-22 23:08 |
0 |
by galp Fri, 2019-02-22 23:08 |
|
Custom application and UART by Dennis Freiburg » Sat, 2020-01-11 13:19 |
3 |
by Dennis Freiburg Sun, 2020-01-12 19:37 |
|
Custom Apps on Windows by rok340 » Tue, 2021-01-26 10:05 |
5 |
by rok340 Fri, 2021-01-29 08:33 |
|
Custom Built ESC based on VESC 6.6 by jordanlow » Sun, 2020-05-03 16:07 |
3 |
by regskd Tue, 2020-07-28 23:35 |
|
Custom code changes- I/O pin go high or low by dsuresh » Thu, 2021-05-13 19:50 |
2 |
by dsuresh Fri, 2021-05-14 22:30 |
|
Custom controlling software by neuromancer2701 » Tue, 2018-09-04 02:09 |
4 |
by LogixCraft Mon, 2022-01-03 13:33 |
|
Custom Display Receiver for VESC by WatEvsCevs » Wed, 2019-08-28 02:29 |
1 |
by frank Fri, 2019-08-30 10:03 |
|
custom firmware by vufmihai » Thu, 2020-01-16 09:06 |
0 |
by vufmihai Thu, 2020-01-16 09:06 |
|
Custom VESC4 hardware - disable Regen? by ben5243 » Mon, 2020-04-13 19:48 |
1 |
by hexakopter Sat, 2020-04-18 16:51 |
|
customer app for pwm input by ccrbs » Tue, 2020-08-11 12:06 |
0 |
by ccrbs Tue, 2020-08-11 12:06 |
|
Cut-out at >40A by thewho » Thu, 2018-09-13 20:24 |
0 |
by thewho Thu, 2018-09-13 20:24 |
|
Dangerous bug when using KILLSWITCH and PPM, FW5.03 by corgon » Wed, 2022-12-14 16:37 |
2 |
by corgon Thu, 2022-12-15 23:10 |
|
DC-Link Capacitor Selection by rushi95 » Sat, 2019-05-18 12:15 |
1 |
by hexakopter Sat, 2019-05-18 12:39 |
|
Dead VESC. Power up when motor is spinning. by Bor Zabric » Mon, 2018-10-08 10:16 |
4 |
by striderkent Fri, 2019-01-11 18:46 |
|
Delayed start for slave motor by rsknudsen-dk » Mon, 2020-04-06 10:06 |
0 |
by rsknudsen-dk Mon, 2020-04-06 10:06 |
|
Delayed Startup with ADC Throttle by Marctwo » Sat, 2020-07-04 21:48 |
10 |
by Marctwo Thu, 2020-07-16 09:18 |
|
Design custom VESC 6 Hardware by brightlightbeam » Sat, 2020-07-04 14:18 |
5 |
by Gatze Mon, 2022-04-18 18:22 |
|
Designing a robust power stage using Mosfets by ripperpc » Tue, 2020-05-05 08:04 |
0 |
by ripperpc Tue, 2020-05-05 08:04 |
|
Device shutting down by gjos » Sun, 2024-04-21 22:23 |
0 |
by gjos Sun, 2024-04-21 22:23 |
|
Did I damage My Vesc? by Kent Church » Tue, 2022-01-11 04:47 |
1 |
by skyline1970 Wed, 2022-01-19 09:46 |
|
Difference between Brake Current, Full Brake etc by wdaehn » Wed, 2018-02-21 15:32 |
4 |
by rodread Sat, 2018-03-03 10:45 |
|
Difference between ERPM and Duty Cycle by dormanae » Wed, 2022-02-23 17:21 |
1 |
by j.konrad Thu, 2022-02-24 02:08 |
Log in to post new content in the forum.