You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Boat indexed throttle - how to connect and what resistance by trolling » Sat, 2018-12-08 19:45 |
0 |
by trolling Sat, 2018-12-08 19:45 |
|
|
vesc free role? by iplayfast » Mon, 2021-02-08 22:13 |
0 |
by iplayfast Mon, 2021-02-08 22:13 |
|
|
Wheel speed over CANBUS by paule » Tue, 2020-12-29 13:04 |
0 |
by paule Tue, 2020-12-29 13:04 |
|
|
Vesc Tools by Don » Sat, 2021-02-13 14:25 |
0 |
by Don Sat, 2021-02-13 14:25 |
|
|
Ayuda configurar vesc tool by julitosanse » Sat, 2021-01-02 13:24 |
0 |
by julitosanse Sat, 2021-01-02 13:24 |
|
|
Lehner TorQstar any experience by fabu80 » Wed, 2023-02-01 08:35 |
0 |
by fabu80 Wed, 2023-02-01 08:35 |
|
|
advice on position control by feskarn » Mon, 2021-02-15 14:47 |
0 |
by feskarn Mon, 2021-02-15 14:47 |
|
|
How to reboot VESC from serial port by Ivko » Mon, 2021-01-04 18:44 |
0 |
by Ivko Mon, 2021-01-04 18:44 |
|
|
AS5047 over SPI pins on VESC six by Jessica » Fri, 2018-12-21 11:10 |
0 |
by Jessica Fri, 2018-12-21 11:10 |
|
|
DIY powerfull vesc for electric motor, Axiom: 100kW motor controller by torlon » Wed, 2023-02-15 02:37 |
0 |
by torlon Wed, 2023-02-15 02:37 |
|
|
Connection issues using PyVESC by axelray » Tue, 2022-12-13 15:15 |
0 |
by axelray Tue, 2022-12-13 15:15 |
|
|
About VESC tool by MaruthiV » Mon, 2023-02-20 08:32 |
0 |
by MaruthiV Mon, 2023-02-20 08:32 |
|
|
Setting PID gains (and other config parameters) over CAN Bus by TheCuriousRobot » Thu, 2022-12-15 22:03 |
0 |
by TheCuriousRobot Thu, 2022-12-15 22:03 |
|
|
Vesc red LED on by dsuresh » Wed, 2021-02-24 18:01 |
0 |
by dsuresh Wed, 2021-02-24 18:01 |
|
|
DRV8302 Gate Pin output waveform is abnormal by yandongyu1998 » Fri, 2019-12-13 07:21 |
0 |
by yandongyu1998 Fri, 2019-12-13 07:21 |
|
|
The rpm control is not working properly by ptss37 » Wed, 2021-11-24 03:30 |
0 |
by ptss37 Wed, 2021-11-24 03:44 |
|
|
Any issues with the DRV8323? by shaman » Thu, 2019-10-24 21:50 |
0 |
by shaman Thu, 2019-10-24 21:50 |
|
|
How to set up RF receiver for PPM or UART input? by adamdorr » Tue, 2020-01-07 16:23 |
0 |
by adamdorr Tue, 2020-01-07 16:23 |
|
|
Vesc WS2812b led issues & support by Ash » Tue, 2019-11-12 08:40 |
0 |
by Ash Tue, 2019-11-12 14:13 |
|
|
Can bus communication. by Piamen » Wed, 2019-11-27 06:47 |
0 |
by Piamen Wed, 2019-11-27 06:47 |
|
|
Unofficial VESC Discord server by kubark42 » Tue, 2021-11-16 16:07 |
0 |
by kubark42 Fri, 2021-11-19 03:12 |
|
|
VESC with asynchronous motors by afbbfa » Fri, 2022-07-29 22:51 |
0 |
by afbbfa Fri, 2022-07-29 22:51 |
|
|
I need clarification on connecting a Magura 0-5k Ohm Pot Twist Throttle to Tronic 250 VESC. by notahorse » Fri, 2022-06-03 08:13 |
0 |
by notahorse Fri, 2022-06-03 08:13 |
|
|
Regenerative braking in scooter Zero x11 72V dual motor 2 x 1600 w peak power 6000W by Makroman » Wed, 2020-07-08 20:00 |
0 |
by Makroman Wed, 2020-07-08 20:00 |
|
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 » Mon, 2022-08-01 18:08 |
0 |
by moose09876 Mon, 2022-08-01 18:08 |
Log in to post new content in the forum.
