You are here

General discussion

Topic / Topic starter Repliessort descending Last post
Normal topic Progetto Vesc
by Matteo Christian » Tue, 2023-05-30 09:20
1
by frank
Wed, 2023-05-31 11:30
Normal topic Canbus slave control in duty cycle mode not working correctly
by Enak » Sat, 2019-04-13 03:55
1
by benjamin
Mon, 2019-04-15 10:09
Normal topic Anyone building DRV8350 based VESC?
by ZacharyDrew » Tue, 2019-04-16 02:14
1
by benjamin
Tue, 2019-04-16 10:14
Normal topic Can't get motor to run using COMM port on vesc 6 MKVI and arduino mega with a potentiometer and SolidGeeks UART library
by Kokonenen » Thu, 2023-03-30 11:41
1
by Kokonenen
Thu, 2023-03-30 16:19
Normal topic New at VESC Tool
by TheButaner » Sun, 2023-06-04 21:38
1
by Gos1
Mon, 2023-06-26 11:37
Normal topic Voltage vs Heating ?
by marko » Thu, 2019-04-25 21:40
1
by moto_guy
Fri, 2019-04-26 06:02
Normal topic Problem cruise with Adaptor 2
by Dominator2 » Sun, 2023-06-18 10:43
1
by Dominator2
Sun, 2023-06-18 14:55
Normal topic [SOLVED, was a mistake] Set ERPM command: issue with the speed controller with higher speed values that is possible with bat vol
by yes_wecangogreen » Wed, 2023-04-12 00:51
1
by yes_wecangogreen
Sat, 2023-04-29 09:24
Normal topic Connecting VESC to XAVIER
by MrMonk3y » Wed, 2019-05-01 09:53
1
by MrMonk3y
Wed, 2019-05-08 13:34
Normal topic VESC 4.12 FW5.02 CAN status messages is spamming bus, external controller, SOLVED: NEEDED INIT!
by Offline » Mon, 2021-05-03 14:57
1
by Offline
Tue, 2021-05-04 10:03
Normal topic Power supply connection for multiple controllers
by Caustic_Zinc » Wed, 2019-05-01 21:06
1
by giganticfizzy
Sat, 2019-09-14 10:53
Normal topic Input Setup Wizard Does Not Ask if Single or Multi VESC
by kylemuramatsu » Wed, 2019-03-13 03:22
1
by benjamin
Wed, 2019-03-13 09:38
Normal topic FSESC 4.12 oscillating and making noise
by hichemhlm » Sun, 2020-03-29 13:33
1
by hichemhlm
Sun, 2020-12-27 12:19
Normal topic Difficulty Tuning HFI on Hoverboard Motor for Low-Speed, High-Torque Application
by Ponps33 » Tue, 2024-11-19 10:29
1
by Thamp33
Tue, 2026-07-14 20:51
Normal topic Can someone please post the steps to do position control from vesc tool?
by dp » Wed, 2022-02-16 14:51
1
by frank
Wed, 2022-02-16 17:24
Normal topic will VESC synch with a 1020 inrunner?
by Oded Mazor » Fri, 2022-02-18 16:58
1
by frank
Fri, 2022-02-18 17:51
Normal topic Newbie Help please, Longer run time?
by Bildoon » Mon, 2020-04-06 02:00
1
by linsus
Thu, 2020-04-16 14:18
Normal topic VESC Tool 2.02 UI Issues?
by AberrantRobotics » Tue, 2020-02-04 16:08
1
by frank
Mon, 2020-02-10 18:16
Normal topic Difference between ERPM and Duty Cycle
by dormanae » Wed, 2022-02-23 17:21
1
by j.konrad
Thu, 2022-02-24 02:08
Normal topic What's general algorithm of firmware?
by Furkan Kaşku » Mon, 2020-02-10 09:20
1
by vadicus
Mon, 2020-02-10 10:20
Normal topic Questions: VESC Android APP And ADC Throttle
by BLeaCH » Mon, 2020-02-17 20:31
1
by BLeaCH
Wed, 2020-02-19 01:38
Normal topic Help, if I accelerate from 0 km/h, I burn out the MOSFETs
by EverL8s » Wed, 2024-06-19 00:34
1
by tokerodev
Tue, 2024-07-09 19:14
Normal topic PAS pinout
by sifourquier » Sat, 2021-12-04 00:56
1
by velolac
Wed, 2021-12-08 00:39
Normal topic Powering a Beckhoff AM3100 Synchronus Servomotor with FOC
by Michael Hamm » Mon, 2022-01-24 10:42
1
by frank
Mon, 2022-01-24 12:36
Normal topic Multiple VESC not working with PAS app?
by radverkehr-labo... » Wed, 2024-10-16 12:57
1
by radverkehr-labo...
Wed, 2024-10-16 13:36
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - General discussion