Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Comments
yt
yt
gh
gh
fg
fg
fg
fg
42
42
fhh
fhh
sg
sg
gh
gh
gj
gj
fh
fh
writing services
Accessing professional Report writing services https://essayhub.com/report-writing-service was a game-changer for me during challenging academic periods. The service provided me with well-researched and expertly written reports that met all my requirements. Thanks to their timely assistance, I was able to submit reports that not only met but exceeded the expectations of my professors, earning accolades for my scholarly contributions.
Sure, setting up multiple
Sure, setting up multiple VESCs via CAN-Bus with a PPM signal radio controller can be a bit tricky, but it's definitely doable with the right guidance. Start by ensuring all VESCs are properly connected and recognized by the system. Then, utilize the Input Setup Wizard to configure each VESC individually, assigning them to the appropriate channels on your radio controller. If you encounter any issues, don't hesitate to ask for help on forums like this one. Also, remember to check compatibility with mods like wicked whims to avoid any conflicts.
hello
Hello friends! Recently, a friend of mine shared with me a place where he often places sports bets offline. Here is the link if you are interested. After visiting this site, I immediately liked it, because I really like nice interfaces in sites, and I consider it a big plus if the site has a simple and beautiful interface! I recommend it
Hello, I want to recommend
Hello, I want to recommend you a site with a large collection of different casinos, which I myself use, it is melbet, they have the most interesting and diverse games, and the probability of winning is very high.There are also sports betting with high odds. There are great bonuses for new users. The site works well and so does the app. you can register here https://melbetph.com/casino/ and start winning right now. Enjoy the game)
The Input Setup Wizard for
The Input Setup Wizard for multiple VESCs via CAN-Bus is a convenient tool for configuring your electronic speed controllers efficiently. With the option to use a PPM signal radio controller, it offers flexibility and ease of use. Plus, don't forget to tubi.tv/activate for endless entertainment options.
This is very nice, indeed
This is very nice, indeed.
Spinner Tools
Alright, setting up multiple
Alright, setting up multiple VESCs via CAN-Bus with a PPM signal radio controller? Piece of cake! We'll dive into the VESC®-Tool Software, configure those genuine VESC® motor controllers, and run them in Current No Reverse with Brake mode. Just follow along, and we'll get those wheels spinning smoothly. Ready? Let's click for more to get started on this setup wizard adventure!
https://answersrepublic.com/education/13-things-and-values-to-look-for-in-a-company/
great
In the game fnaf, players take on the role of a security guard assigned to watch over a restaurant at night, where animated mascots come to life and roam the halls.
thank you very much
I am following the instructions step by step to set up VESC in the most accurate way, but unfortunately in some steps the illustrations are no longer viewable. I a sedecordle lot really hope you will update it as soon as possible maybe.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
games
Hello friends! betting in kenya has impressed me with its innovative approach to sports betting. The site offers not only a large selection of events and high odds, but also a user-friendly interface that makes the game even more exciting. An important advantage is the legal status of the site, which guarantees the protection of my rights and the security of my personal data. I also appreciate the variety of payment methods that allow me to deposit funds and withdraw winnings quickly and conveniently. I recommend this site to anyone looking for an innovative and convenient betting service!
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
4. Input Setup Wizard for
4. Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller
Configuration of your VESC® or VESC® based ESC using the VESC®-Tool Software.
In this tutorial we will configure multiple genuine VESC® motor controllers, using a CAN bus link cable. We will use a PPM signal based radio controller and will run the VESCs in Current No Reverse with Brake mode.
Make sure to use the latest VESC-Tool version!
Download from http://www.vesc-project.com/vesc_tool
Important Notice:
Run the Motor Setup Wizard on each VESC first.
Never connect a receiver or other devices to multiple VESCs (e.g. Y-PPM). Use CAN-Bus instead.
Only connect CANH and CANL In the CAN connector. 5V and GND should be left unconnected.
Failing to follow these instructions may damage your VESC (s) permanently.
Now we will start to configure the master VESC. This is the VESC with the input device (e.g.reciever) attached.
Connect your master VESC® to your computer using a mini/micro USB cable.
Mini USB is used for HW 4.xx only. Some cheap micro USB cables are designed for charging your
phone and will not work properly! Try another cable if you experience any issues.
Run the VESC®-Tool software.
This is the next screen you will see.
Now we will configure the slave VESC.
Plug your USB-Cable into the slave VESC. Make sure both VESCs are powered up and connected via CAN bus cable.
Congratulations, your VESCs are now ready to operate. If you like you can follow the
Throttle curves and other tweaks manual for further improvements.
Adjustments for the input device (App settings) are configured on the master VESC.
Pages