You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
FloatWheel not balancing, shooting forward by EvDeck on Fri, 2023-04-14 22:16 |
2 |
by Surefire Sun, 2023-07-09 05:59 |
General discussion | |
Flux linkage detection failed by Count1310 on Sat, 2020-08-22 16:30 |
3 |
by drummerboy5408 Wed, 2022-04-13 07:42 |
General discussion | |
flux linkage detection failled by Clsprinkler@aol.com on Tue, 2020-10-20 03:02 |
1 |
by Kent Tabor Wed, 2020-10-21 04:36 |
VESC Tool | |
Flux linkage observer @ low speed by soltesz on Sun, 2017-12-17 16:33 |
9 |
by benjamin Thu, 2017-12-21 10:17 |
VESC Firmware | |
FOC : Stop Motor without Active Brake by Flyingtux on Mon, 2022-03-14 12:35 |
4 |
by Flyingtux Tue, 2022-03-15 23:09 |
General discussion | |
FOC alignment and startup by nami1216 on Mon, 2020-03-30 10:40 |
1 |
by kaanozgen Tue, 2020-03-31 10:57 |
VESC Firmware | |
FOC and extremely low speeds do not look sinusoidal by wdaehn on Wed, 2017-11-29 21:33 |
11 |
by Benjamin Mahony Wed, 2018-01-10 01:19 |
General discussion | |
FOC and RC Helicopter (25KG) by Flyingtux on Tue, 2022-03-15 23:30 |
2 |
by Flyingtux Tue, 2022-03-29 17:12 |
General discussion | |
FOC and very low speeds by verbeek on Mon, 2018-07-09 16:17 |
18 |
by Chris Barth Fri, 2023-11-10 04:45 |
General discussion | |
FOC braking problem (FAULT_CODE_DRV) by iscle on Tue, 2018-05-29 15:16 |
29 |
by Zanooon97 Sat, 2023-03-18 20:11 |
General discussion | |
FOC bugs by Antoine0106 on Sat, 2019-08-24 18:30 |
2 |
by Stupidspencer Thu, 2019-09-12 17:51 |
General discussion | |
FOC Calibration over CAN by thisisjaye on Fri, 2018-10-26 13:15 |
1 |
by frank Fri, 2018-10-26 17:12 |
General discussion | |
FOC configuration - Motor stalls during measurement by Lukinio on Wed, 2021-05-26 12:31 |
1 |
by Lukinio Wed, 2021-05-26 12:44 |
VESC Tool | |
FOC configuration when resistance is measured as R=0. by Roger Wolff on Tue, 2018-08-28 18:20 |
2 |
by Foxyirish1987 Tue, 2020-04-07 13:12 |
VESC Tool | |
FOC control Speed and D-axis current oscillations by sxv9616 on Tue, 2019-12-03 22:14 |
2 |
by sxv9616 Thu, 2019-12-05 17:12 |
VESC6 Beta | |
FOC current oscillation at max. speed by ProgramThyself on Mon, 2020-08-10 05:55 |
10 |
by SRFirefox Wed, 2020-08-26 23:10 |
General discussion | |
FOC detection error " R is 0" by MontPierre on Fri, 2017-09-08 19:52 |
38 |
by danielhugentobler Sat, 2022-01-01 23:13 |
VESC Tool | |
FOC detection needs load? by tuloski on Thu, 2018-09-13 10:19 |
1 |
by TechAUmNu Thu, 2018-09-13 12:26 |
VESC Tool | |
FOC detection not working, "L=0" by chundri on Tue, 2021-01-12 15:02 |
2 |
by chundri Wed, 2021-01-13 15:40 |
VESC Tool | |
foc detection params by stefann on Mon, 2020-04-13 00:07 |
by stefann Mon, 2020-04-13 00:28 |
VESC Tool |