You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
How to set max input voltage to over 57 volts? by johnny5in5 on Thu, 2020-09-24 03:34 |
3 |
by TheFallen Mon, 2021-03-01 16:42 |
VESC Tool | |
Vesc Tool Mobile can't update Vesc Firmware by Happy Giraffe on Wed, 2022-01-19 21:48 |
2 |
by Happy Giraffe Thu, 2022-01-20 23:50 |
VESC Tool | |
Driving Alternator wired as BLDC motor with VESC6 by LittleTinker on Thu, 2019-10-10 13:06 |
6 |
by flyingbrike Wed, 2021-09-22 20:16 |
VESC Tool | |
Phase Correct PWM Setting? by orangepig111 on Tue, 2021-07-20 07:39 |
1 |
by skyline1970 Fri, 2021-10-29 12:52 |
VESC Tool | |
How to control motor using VESC tool in computer at constant rpm? by vimi94 on Wed, 2019-05-01 12:56 |
3 |
by foreclosurecat Tue, 2022-12-06 22:36 |
VESC Tool | |
Multiple VESC's in duty cycle mode by Rudolf10000 on Sat, 2019-04-20 13:24 |
1 |
by Rudolf10000 Mon, 2019-04-29 19:34 |
VESC Tool | |
ADC MAX Voltage 5volt ? by liteglow on Sat, 2020-07-25 23:48 |
by liteglow Sat, 2020-07-25 23:48 |
VESC Tool | ||
Vesc efficiency through log (.CSV) by th0masrtg on Tue, 2022-11-22 10:08 |
by th0masrtg Tue, 2022-11-22 10:08 |
VESC Tool | ||
Vesc tool 1.26.. issue with firmware updates? by beetbocks on Tue, 2019-12-17 10:17 |
2 |
by Stupidspencer Wed, 2019-12-25 23:04 |
VESC Tool | |
FOC with 2 Poles and only 6 Windings? by martin2day on Fri, 2020-07-17 08:16 |
2 |
by martin2day Sat, 2020-07-18 10:36 |
VESC Tool | |
vesc tool 1.25 not opening. by osis on Tue, 2019-10-29 20:50 |
9 |
by flyingbrike Wed, 2021-09-08 09:06 |
VESC Tool | |
cant connect via usb by curtm on Wed, 2019-06-19 03:05 |
2 |
by curtm Thu, 2019-07-04 00:37 |
VESC Tool | |
FOC configuration when resistance is measured as R=0. by Roger Wolff on Tue, 2018-08-28 18:20 |
2 |
by Foxyirish1987 Tue, 2020-04-07 13:12 |
VESC Tool | |
Full Brake vs Switch Off by meisterpro on Mon, 2021-03-22 14:36 |
by meisterpro Mon, 2021-03-22 14:36 |
VESC Tool | ||
terminal command via UART for a gimbal by fredfred on Sat, 2021-12-18 20:49 |
by fredfred Sat, 2021-12-18 20:49 |
VESC Tool | ||
Can't find good parameters for FOC detection by Kabroc on Thu, 2020-04-30 16:28 |
by Kabroc Thu, 2020-04-30 16:28 |
VESC Tool | ||
UART Safety Feature by jaghori.sasan on Wed, 2019-09-04 18:45 |
by jaghori.sasan Wed, 2019-09-04 18:45 |
VESC Tool | ||
VESCTOOL - Multiple VESC simultaneous configuration (Same CANBUS ID issues) by Filcas on Thu, 2021-02-18 20:52 |
2 |
by Filcas Fri, 2021-02-19 01:37 |
VESC Tool | |
Motor whine with HFI? by christopher.h.poole on Mon, 2021-04-19 15:49 |
2 |
by christopher.h.poole Tue, 2021-06-15 21:18 |
VESC Tool | |
FSESC seems to be speed limiting my motor by 5amsung4 on Sat, 2022-09-03 18:50 |
by 5amsung4 Mon, 2022-09-05 07:51 |
VESC Tool |