You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Writing to slave vesc sometimes cause loss of can bus by meashman on Wed, 2022-07-20 01:08 |
2 |
by frank Thu, 2022-10-27 08:54 |
VESC Tool | |
Vesc Tool not opening on windows computer by maccert on Sat, 2019-03-02 11:04 |
2 |
by Luca Torani Sun, 2019-03-03 20:32 |
VESC Tool | |
foc openloop not starting motor on higher erpm by Alan oldguy on Thu, 2018-09-06 08:43 |
8 |
by technicc Mon, 2022-03-28 09:23 |
VESC Tool | |
Motor temperature, how to set limit >120 C ? by RSR on Wed, 2018-08-22 12:40 |
3 |
by Danny Bokma Thu, 2018-08-23 07:19 |
VESC Tool | |
Get data from VESC on Arduino by jhanvisharma on Wed, 2021-04-07 08:25 |
1 |
by CTSchorsch Wed, 2021-04-07 09:05 |
VESC Tool | |
Plz Help Me, im at the end of my rope.....(Flipsky 4.12) by curtiswooden35 on Wed, 2022-08-03 03:23 |
1 |
by frank Wed, 2022-08-03 14:32 |
VESC Tool | |
Version 2.03 won't open by marialoise on Fri, 2020-03-13 20:24 |
5 |
by pwilkinson91 Tue, 2023-06-27 22:07 |
VESC Tool | |
NRF connection error by Denn on Wed, 2022-02-02 11:17 |
by Denn Wed, 2022-02-02 11:17 |
VESC Tool | ||
Bluetooth connection possible with METR device? by Cuprani on Sun, 2018-04-01 23:00 |
1 |
by Pimousse Wed, 2018-04-04 11:34 |
VESC Tool | |
Fault Codes by Joe_Lowtech on Wed, 2019-02-13 20:06 |
2 |
by mthielvoldt Thu, 2019-07-18 00:38 |
VESC Tool | |
FOC detection not working, "L=0" by chundri on Tue, 2021-01-12 15:02 |
2 |
by chundri Wed, 2021-01-13 15:40 |
VESC Tool | |
Old versions of VESC Tool by TheFallen on Thu, 2018-07-05 19:47 |
29 |
by frank Wed, 2022-09-21 09:10 |
VESC Tool | |
FOC Encoder autotune issue by David_Lo on Tue, 2020-01-21 11:54 |
by David_Lo Tue, 2020-01-21 11:54 |
VESC Tool | ||
Hall sensor data is all 0. What do? by Byproduct on Sat, 2023-01-14 14:39 |
by Byproduct Wed, 2023-02-08 11:21 |
VESC Tool | ||
PPM Configuration is Only Working While Connected to VESC Software by kyle45 on Wed, 2020-01-15 05:13 |
2 |
by frank Mon, 2020-01-27 21:03 |
VESC Tool | |
Wrong Motor detection values after STM swap dual vesc 6 by Micro on Sun, 2019-08-18 01:59 |
by Micro Sun, 2019-08-18 02:14 |
VESC Tool | ||
Data Loggin Values by BLeaCH on Sat, 2020-04-04 07:37 |
by BLeaCH Sat, 2020-04-04 07:37 |
VESC Tool | ||
PPM Mapping by russell.morris1... on Tue, 2021-09-14 22:38 |
by russell.morris1... Tue, 2021-09-14 22:38 |
VESC Tool | ||
VESC Tool crashes when loading/saving motor/app config by bkyrevolution on Thu, 2023-03-02 20:27 |
1 |
by jimtzer Mon, 2023-03-13 00:30 |
VESC Tool | |
FOC detection error " R is 0" by MontPierre on Fri, 2017-09-08 19:52 |
38 |
by danielhugentobler Sat, 2022-01-01 23:13 |
VESC Tool |