You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Axial Flux motor control mode by ardillolambo on Wed, 2022-03-02 13:59 |
4 |
by ardillolambo Wed, 2022-03-02 18:25 |
VESC Original Hardware | |
|
Differential steering setup by GCTech on Sat, 2020-07-04 17:38 |
4 |
by CalLangford Fri, 2024-09-20 20:29 |
General discussion | |
|
Vesc tool not working by faheemift on Sun, 2021-02-14 14:44 |
4 |
by faheemift Wed, 2021-04-14 22:59 |
General discussion | |
|
version of the vesc tool by aysubscriber@ic... on Tue, 2017-10-03 07:53 |
4 |
by aysubscriber@ic... Fri, 2017-10-13 03:47 |
General discussion | |
|
FOC wizard confusion by Stupidspencer on Mon, 2019-07-08 04:18 |
4 |
by lurch Sun, 2021-10-24 14:46 |
VESC Tool | |
|
MOSFET failure and replacement, stormcore 60d by Airatic on Wed, 2022-01-19 11:36 |
4 |
by j.konrad Sat, 2022-01-22 01:17 |
General discussion | |
|
VESC Tool Instructions by brschaefer74 on Fri, 2019-01-25 03:49 |
4 |
by sam.vanratt Sat, 2019-01-26 12:52 |
General discussion | |
|
Lag using the Input Setup Wizard (APP) by Oyta on Wed, 2017-06-28 22:01 |
4 |
by sl33py Thu, 2017-07-06 02:12 |
VESC6 Beta | |
|
Smooth control 3 phase sensored motor by spacewalker on Thu, 2020-07-23 07:25 |
4 |
by vadicus Fri, 2020-11-13 19:18 |
General discussion | |
|
Lowest power/smallest available 3rd party board? by doctarr on Sun, 2021-03-07 15:28 |
4 |
by doctarr Mon, 2021-03-08 12:38 |
Third Party Hardware | |
|
ADC control not linear or smooth by arranto12 on Sat, 2021-11-13 23:23 |
4 |
by TechAUmNu Sun, 2021-11-14 01:03 |
General discussion | |
|
VESC help offered for private persons and companies by electricfox on Thu, 2023-10-05 17:41 |
4 |
by Tripod6813 Tue, 2023-10-17 13:17 |
General discussion | |
|
Can't receive status message via CAN bus by IanG on Mon, 2020-04-13 03:50 |
4 |
by olivierabristol Sun, 2022-02-27 08:31 |
General discussion | |
|
VESC6 Issues: Battery current inaccurate, positive ramp time, motor current max. by ESCam on Thu, 2019-03-21 22:50 |
4 |
by sp3swj Sat, 2022-03-19 15:07 |
VESC Original Hardware | |
|
Why use sensorless if the motor has sensors? by j.konrad on Thu, 2022-02-17 14:25 |
4 |
by j.konrad Mon, 2022-02-21 15:06 |
General discussion | |
|
CANopen integration by blevruz on Wed, 2022-10-05 10:33 |
4 |
by nirm Sun, 2024-08-04 18:21 |
VESC Development and Beta Testing | |
|
throttle set up by TONY61 on Wed, 2024-12-11 16:48 |
4 |
by Jamesavery22 Sun, 2025-01-05 10:54 |
General discussion | |
|
Custom hardware flash problems by brightlightbeam on Mon, 2021-01-25 17:25 |
4 |
by brightlightbeam Thu, 2021-01-28 12:00 |
Third Party Hardware | |
|
enertionboard focbox : is vesc_tool safe to use? by fourchette on Wed, 2018-11-07 23:49 |
4 |
by fourchette Tue, 2018-11-20 21:13 |
General discussion | |
|
PPM duty cycle option not being stored in EEPROM by wjpremerlani on Wed, 2022-06-08 12:49 |
4 |
by frank Thu, 2022-06-09 09:07 |
General discussion |
Pages
