You are here

Active forum topics

Topic Replies Last post Forumsort descending
Normal topic Serial port errors with VESC Tool 3.00 and Flipsky FSESC 7550
by mckenzie.keith on Thu, 2022-01-06 02:24
1 by mckenzie.keith
Thu, 2022-01-06 18:54
VESC Tool
Normal topic VESC failure presumably due to current oscillations at high current
by rsarver on Wed, 2021-03-24 22:06
by rsarver
Wed, 2021-03-24 22:06
VESC Tool
Normal topic Vesctool otg
by meashman on Sat, 2022-08-06 10:05
2 by meashman
Wed, 2022-08-17 06:39
VESC Tool
Normal topic Cruise Control button no longer working
by Jobbel on Tue, 2017-09-05 01:10
1 by Jobbel
Sun, 2022-09-25 16:36
VESC Tool
Normal topic Acceleration ramping using UART communication with arduino on VTool 6.0
by Kokonenen on Tue, 2023-04-04 11:48
1 by Kokonenen
Tue, 2023-04-04 14:30
VESC Tool
Sticky topic FOC wizard confusion
by Stupidspencer on Mon, 2019-07-08 04:18
4 by lurch
Sun, 2021-10-24 14:46
VESC Tool
Normal topic Overheating protection, voltage-/current-limitation etc.
by kianK on Thu, 2021-04-15 07:23
2 by lilliamhoyle
Wed, 2021-07-07 09:36
VESC Tool
Normal topic version of Vesc Tool for Flipsky 6.6
by Robert Adkins on Sun, 2019-09-29 18:13
3 by frank
Wed, 2019-10-23 09:35
VESC Tool
Normal topic Voltage measurement calibration?
by pyryjansson on Tue, 2019-04-30 20:19
2 by frank
Wed, 2022-11-30 09:55
VESC Tool
Normal topic FOC detection....
by Roger Wolff on Thu, 2018-05-24 17:37
3 by TechAUmNu
Sun, 2018-05-27 21:14
VESC Tool
Normal topic Taking 5-6 seconds for running motor under ADC mode
by asnamp on Fri, 2022-06-24 13:02
1 by skyline1970
Thu, 2022-11-24 21:24
VESC Tool
Normal topic Vesc Tool For Mac
by kmfpod on Tue, 2022-06-14 22:06
1 by frank
Wed, 2022-06-15 09:58
VESC Tool
Normal topic Version 2.03 won't open
by marialoise on Fri, 2020-03-13 20:24
5 by pwilkinson91
Tue, 2023-06-27 22:07
VESC Tool
Normal topic NRF connection error
by Denn on Wed, 2022-02-02 11:17
by Denn
Wed, 2022-02-02 11:17
VESC Tool
Normal topic Fault Codes
by Joe_Lowtech on Wed, 2019-02-13 20:06
2 by mthielvoldt
Thu, 2019-07-18 00:38
VESC Tool
Normal topic FOC detection not working, "L=0"
by chundri on Tue, 2021-01-12 15:02
2 by chundri
Wed, 2021-01-13 15:40
VESC Tool
Hot topic Old versions of VESC Tool
by TheFallen on Thu, 2018-07-05 19:47
31 by rafeh1
Thu, 2024-10-10 23:44
VESC Tool
Normal topic FOC Encoder autotune issue
by David_Lo on Tue, 2020-01-21 11:54
by David_Lo
Tue, 2020-01-21 11:54
VESC Tool
Normal topic Hall sensor data is all 0. What do?
by Byproduct on Sat, 2023-01-14 14:39
by Byproduct
Wed, 2023-02-08 11:21
VESC Tool
Normal topic PPM Configuration is Only Working While Connected to VESC Software
by kyle45 on Wed, 2020-01-15 05:13
2 by frank
Mon, 2020-01-27 21:03
VESC Tool

Pages

Subscribe to Active forum topics