You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
GPL, access to sources. by frank on Mon, 2018-04-23 09:13 |
11 |
by frank Tue, 2020-09-22 08:55 |
The VESC-Project | |
|
LSM6DS3 gyro ? for balancing by amaussa on Sun, 2020-09-13 12:51 |
1 |
by amaussa Mon, 2020-09-21 17:21 |
VESC Tool | |
|
Motor cogs with no load, especially at high rpm by jurya on Fri, 2020-09-18 17:49 |
2 |
by jurya Fri, 2020-09-18 20:40 |
General discussion | |
|
Autodetection algorithm by Griffen on Thu, 2019-01-03 18:44 |
2 |
by Gmack Fri, 2020-09-18 16:39 |
VESC Tool | |
|
Block waves with FOC by spacemango on Fri, 2020-06-26 09:48 |
4 |
by Lisa1812 Fri, 2020-09-18 11:56 |
General discussion | |
|
Compatibility Question by Alexandre Borowczyk on Wed, 2020-09-16 20:06 |
1 |
by vadicus Wed, 2020-09-16 21:17 |
General discussion | |
|
Duty siren via CAN bus listener? by dammfine on Wed, 2020-09-16 19:00 |
1 |
by vadicus Wed, 2020-09-16 21:15 |
General discussion | |
|
Choppiness in motor after half throttle by popeye243 on Tue, 2020-08-04 04:04 |
5 |
by vadicus Tue, 2020-09-15 23:53 |
General discussion | |
|
Hub motor stutters at low RPM by winpark on Wed, 2020-09-02 00:53 |
3 |
by vadicus Tue, 2020-09-15 18:14 |
General discussion | |
|
Sudden kick (from motor current cut off?) by darowi on Mon, 2017-10-02 18:56 |
5 |
by darowi Tue, 2020-09-15 12:45 |
General discussion | |
|
Bluetooth 4 remote by bob23 on Fri, 2020-09-04 02:19 |
20 |
by vadicus Mon, 2020-09-14 22:14 |
Third Party Hardware | |
|
Setup for very slow < 100RPM on Maytech 6365 Motor. by jason3w on Tue, 2020-09-01 10:52 |
2 |
by asapereira Mon, 2020-09-14 10:26 |
VESC Tool | |
|
75/300 R3 and metr.at wird iOS metr App by nice2cu on Sun, 2020-09-13 20:51 |
by nice2cu Sun, 2020-09-13 20:51 |
VESC Original Hardware | ||
|
Duty Cycle Acceleration Limit by jfaille on Tue, 2020-06-16 23:17 |
3 |
by amaussa Sun, 2020-09-13 12:59 |
VESC Tool | |
|
Summerboard VESC Problems by teijidude on Sat, 2020-09-12 22:19 |
by teijidude Sat, 2020-09-12 22:19 |
Third Party Hardware | ||
|
Save state data on vesc? by NuRxG on Thu, 2020-04-09 06:44 |
4 |
by ProgramThyself Sat, 2020-09-12 08:42 |
VESC Development and Beta Testing | |
|
Change some VESC configurations by nltb on Fri, 2020-09-11 13:39 |
by nltb Fri, 2020-09-11 13:39 |
VESC Firmware | ||
|
Adding two reed contacts and adapting the software accordingly by WulfKraneis on Sun, 2020-09-06 16:25 |
1 |
by district9prawn Fri, 2020-09-11 13:15 |
Feature Requests | |
|
Electric scooter controller by saenz4931@gmail.com on Thu, 2020-09-10 05:58 |
by saenz4931@gmail.com Thu, 2020-09-10 05:58 |
Feature Requests | ||
|
75/300 Layout or gerbers by Chapel81 on Fri, 2020-08-28 21:27 |
3 |
by Chapel81 Wed, 2020-09-09 16:24 |
VESC Original Hardware |
Pages
