You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
How to reboot VESC from serial port by Ivko on Mon, 2021-01-04 18:44 |
by Ivko Mon, 2021-01-04 18:44 |
General discussion | ||
|
AS5047 Encoder with VESC 4.20 by rctestflight on Mon, 2020-09-21 19:55 |
1 |
by aparanjpe Sun, 2021-01-03 17:45 |
General discussion | |
|
Why not using interrupt for Hall signal detection? by kuan on Sun, 2021-01-03 09:51 |
by kuan Sun, 2021-01-03 09:51 |
General discussion | ||
|
Ayuda configurar vesc tool by julitosanse on Sat, 2021-01-02 13:24 |
by julitosanse Sat, 2021-01-02 13:24 |
General discussion | ||
|
How do I compile the VESC Tool? by ipbyrne on Wed, 2019-07-24 16:58 |
4 |
by a.dahhak Fri, 2021-01-01 15:25 |
VESC Tool | |
|
Cannot detect VESC with built-in NRF24 from VESC Tool (Android) by fdumi on Wed, 2020-12-30 11:57 |
by fdumi Wed, 2020-12-30 19:00 |
VESC Firmware | ||
|
compatability assistance by NRGFPV on Mon, 2020-12-28 04:58 |
2 |
by NRGFPV Wed, 2020-12-30 08:46 |
Third Party Hardware | |
|
Truncated maximum motor current values by kaxorpie on Sun, 2020-12-27 23:28 |
5 |
by kaxorpie Wed, 2020-12-30 00:16 |
Feature Requests | |
|
Where to find CAN protocol documentation? by doctarr on Tue, 2020-12-29 15:33 |
by doctarr Tue, 2020-12-29 15:33 |
General discussion | ||
|
Wheel speed over CANBUS by paule on Tue, 2020-12-29 13:04 |
by paule Tue, 2020-12-29 13:04 |
General discussion | ||
|
Trasmitter not able to communicate with VESC by Andrea on Thu, 2020-03-26 20:22 |
1 |
by TheFallen Mon, 2020-12-28 16:16 |
VESC Tool | |
|
How to wire MPU-9250 9DoF using SPI to vesc 6 mk4 by zmei116 on Fri, 2020-08-28 12:17 |
6 |
by TheFallen Mon, 2020-12-28 06:22 |
VESC Original Hardware | |
|
FSESC 4.12 oscillating and making noise by hichemhlm on Sun, 2020-03-29 13:33 |
1 |
by hichemhlm Sun, 2020-12-27 12:19 |
General discussion | |
|
75/300 R2 FW higher than 3.62 ? it is possible? by Lasse on Sat, 2020-12-26 20:34 |
by Lasse Sat, 2020-12-26 20:34 |
VESC Firmware | ||
|
Hall sensors + incremental encoder by SAK-SIVAL on Thu, 2020-10-08 18:37 |
2 |
by tonyXHB Tue, 2020-12-22 13:33 |
General discussion | |
|
VESC 75/300 Overheating issues by tecnico.solarboat on Sat, 2020-10-17 00:52 |
12 |
by Gerhard Tue, 2020-12-22 13:19 |
VESC Original Hardware | |
|
Complete lack of torque on DIY e-bike by Frazatto on Fri, 2020-09-18 21:01 |
6 |
by tonyXHB Tue, 2020-12-22 13:18 |
General discussion | |
|
Vesc board on ebike by tailele on Sat, 2020-11-14 15:08 |
2 |
by tonyXHB Tue, 2020-12-22 12:21 |
General discussion | |
|
VESC kickback by Farmer_Mayer on Tue, 2020-12-22 01:16 |
by Farmer_Mayer Tue, 2020-12-22 01:16 |
General discussion | ||
|
Problem with St Link v2 Connetion (solved) by Izuke on Sun, 2018-04-15 22:31 |
7 |
by maple_leaf Mon, 2020-12-21 16:19 |
VESC Firmware |
Pages
