You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Bluetooth 4 remote by bob23 on Fri, 2020-09-04 02:19 |
20 |
by vadicus Mon, 2020-09-14 22:14 |
Third Party Hardware | |
|
Setup for very slow < 100RPM on Maytech 6365 Motor. by jason3w on Tue, 2020-09-01 10:52 |
2 |
by asapereira Mon, 2020-09-14 10:26 |
VESC Tool | |
|
75/300 R3 and metr.at wird iOS metr App by nice2cu on Sun, 2020-09-13 20:51 |
by nice2cu Sun, 2020-09-13 20:51 |
VESC Original Hardware | ||
|
Duty Cycle Acceleration Limit by jfaille on Tue, 2020-06-16 23:17 |
3 |
by amaussa Sun, 2020-09-13 12:59 |
VESC Tool | |
|
Summerboard VESC Problems by teijidude on Sat, 2020-09-12 22:19 |
by teijidude Sat, 2020-09-12 22:19 |
Third Party Hardware | ||
|
Save state data on vesc? by NuRxG on Thu, 2020-04-09 06:44 |
4 |
by ProgramThyself Sat, 2020-09-12 08:42 |
VESC Development and Beta Testing | |
|
Change some VESC configurations by nltb on Fri, 2020-09-11 13:39 |
by nltb Fri, 2020-09-11 13:39 |
VESC Firmware | ||
|
Adding two reed contacts and adapting the software accordingly by WulfKraneis on Sun, 2020-09-06 16:25 |
1 |
by district9prawn Fri, 2020-09-11 13:15 |
Feature Requests | |
|
Electric scooter controller by saenz4931@gmail.com on Thu, 2020-09-10 05:58 |
by saenz4931@gmail.com Thu, 2020-09-10 05:58 |
Feature Requests | ||
|
75/300 Layout or gerbers by Chapel81 on Fri, 2020-08-28 21:27 |
3 |
by Chapel81 Wed, 2020-09-09 16:24 |
VESC Original Hardware | |
|
Need Help Setting Up Dual VESC on Trampa by MIKEtheBIKE on Wed, 2020-09-09 03:15 |
by MIKEtheBIKE Wed, 2020-09-09 03:15 |
VESC Tool | ||
|
BRAND NEW R SPEC DUAL 6355 (4.12 VESC) SET UP ISSUES by rodriguezjoe1@b... on Mon, 2020-09-07 17:50 |
by rodriguezjoe1@b... Mon, 2020-09-07 17:50 |
General discussion | ||
|
swagatron hoverboard motors with VESC by popeye243 on Tue, 2020-07-21 02:49 |
13 |
by popeye243 Mon, 2020-09-07 03:42 |
General discussion | |
|
Current out of Sync by CTSchorsch on Sat, 2020-08-01 13:24 |
18 |
by CTSchorsch Fri, 2020-09-04 11:28 |
Third Party Hardware | |
|
Limit Max RPM on a Brushed Motor in DC Mode by KirkusMaximus on Fri, 2020-09-04 02:52 |
by KirkusMaximus Fri, 2020-09-04 02:58 |
General discussion | ||
|
outdated vesc firmware troubles by alybruce on Sun, 2018-10-28 13:06 |
4 |
by Jose Dominguez Fri, 2020-09-04 00:58 |
VESC Firmware | |
|
IMU and balancing powertrain by sunsam8 on Thu, 2020-09-03 05:03 |
by sunsam8 Thu, 2020-09-03 05:03 |
Feature Requests | ||
|
Reprogram VESC for sensorless motor by Christopherinco... on Thu, 2020-09-03 00:10 |
2 |
by vadicus Thu, 2020-09-03 01:14 |
General discussion | |
|
Why does the 75/300 have VCC at 3.4V? by TechAUmNu on Tue, 2020-03-31 14:01 |
3 |
by TechAUmNu Wed, 2020-09-02 12:04 |
VESC Original Hardware | |
|
Do you know how wire simultaneously bluetooth module and 9dof sensor? Bluetooth now connected to TX RX, but it is the same pins by zmei116 on Thu, 2020-08-27 18:02 |
2 |
by TheFallen Sun, 2020-08-30 19:33 |
VESC Original Hardware |
Pages
