You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Can't seem to downgrade firmware on my VESC 6 MKV by curiousgeorge on Thu, 2021-12-02 08:46 |
4 |
by curiousgeorge Fri, 2021-12-03 19:00 |
VESC Firmware | |
Can't spin both motors over CAN-bus by Kokonenen on Wed, 2023-04-19 11:19 |
3 |
by Kokonenen Fri, 2023-04-21 09:18 |
VESC Tool | |
Can't start a sensorless motor of a scooter by tobe81cwb on Mon, 2022-05-02 03:25 |
1 |
by skyline1970 Thu, 2022-11-24 21:36 |
General discussion | |
Can't Update Firmware by indianboy42 on Mon, 2024-06-17 08:54 |
by indianboy42 Mon, 2024-06-17 08:54 |
General discussion | ||
Can't update firmware FSESC 4.12 by TimBilliet on Tue, 2019-11-26 21:52 |
1 |
by TechAUmNu Wed, 2019-11-27 14:47 |
Third Party Hardware | |
Can't update the VESC firmware by mansolander on Thu, 2020-03-05 11:30 |
1 |
by mansolander Fri, 2020-03-06 11:24 |
VESC Tool | |
Can-bus by Sanjoy on Tue, 2017-06-06 21:51 |
1 |
by frank Tue, 2017-06-06 22:50 |
VESC6 Beta | |
CANBUS communication documentation by Dillon on Sun, 2017-08-27 17:50 |
11 |
by Vinayak Bhat Wed, 2023-02-22 13:46 |
VESC6 Beta | |
Canbus slave control in duty cycle mode not working correctly by Enak on Sat, 2019-04-13 03:55 |
1 |
by benjamin Mon, 2019-04-15 10:09 |
General discussion | |
Cannot change CAN Baudrate, Maytech SUPERFOC6.8 by sivanhere on Thu, 2023-03-23 08:12 |
5 |
by frank Mon, 2023-03-27 09:28 |
General discussion | |
Cannot connect to vesc tool app by sharpshooterjd on Fri, 2022-07-29 23:39 |
1 |
by skyline1970 Sun, 2022-11-27 16:38 |
VESC Tool | |
Cannot connect to VESC via USB or SWD by hagis on Wed, 2020-09-23 17:21 |
by hagis Wed, 2020-09-23 17:21 |
General discussion | ||
Cannot detect VESC with built-in NRF24 from VESC Tool (Android) by fdumi on Wed, 2020-12-30 11:57 |
by fdumi Wed, 2020-12-30 19:00 |
VESC Firmware | ||
Cannot downgrade from 5.03 to 5.02 by kallep on Sat, 2022-02-26 19:08 |
5 |
by frank Sat, 2022-03-12 12:09 |
General discussion | |
Cannot downgrade from beta firmware by CasperK on Tue, 2022-08-16 16:56 |
2 |
by joeker24 Mon, 2022-09-05 14:09 |
VESC Firmware | |
Cannot get any PPM signals from Arduino. Or is it just the VESC tool? by MaxMaker1 on Thu, 2018-06-21 23:06 |
4 |
by tuloski Thu, 2018-09-13 09:36 |
VESC Tool | |
Cannot reach max speed of BLDC motor by rousha42 on Wed, 2021-11-03 20:23 |
4 |
by frank Tue, 2021-11-09 09:46 |
General discussion | |
Cannot read data over UART by amalbers01 on Sat, 2022-04-16 05:03 |
1 |
by frank Sat, 2022-04-16 20:06 |
VESC Firmware | |
Cannot start motor - huge current spikes through motor by TechAUmNu on Thu, 2017-11-09 22:57 |
30 |
by e-biker Wed, 2018-02-07 11:56 |
Third Party Hardware | |
Cannot update to FW5.2. by Ba1tuks on Thu, 2021-03-04 21:09 |
3 |
by dsuresh Mon, 2021-04-05 16:43 |
VESC Firmware |