You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
controlling 2 motors for two directions each by ori harush on Mon, 2022-06-06 07:17 |
4 |
by Indy8976 Tue, 2022-06-21 13:36 |
General discussion | |
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 on Wed, 2023-04-12 16:28 |
by Tom65 Wed, 2023-04-12 16:28 |
General discussion | ||
|
VESC Battery Packs by frank on Tue, 2020-10-13 15:21 |
8 |
by zhivko Sat, 2024-08-10 21:14 |
General discussion | |
|
Custom code changes- I/O pin go high or low by dsuresh on Thu, 2021-05-13 19:50 |
2 |
by dsuresh Fri, 2021-05-14 22:30 |
General discussion | |
|
can not start motor with high duty by qdxiatao on Sat, 2018-03-24 03:58 |
by qdxiatao Sat, 2018-03-24 03:58 |
General discussion | ||
|
VESC - Motor will not start until a small kick is applied from a full stop despite using hall sensors by 010203040506070809 on Wed, 2019-10-23 23:12 |
by 010203040506070809 Wed, 2019-10-23 23:12 |
General discussion | ||
|
vesc tool not giving me the right values by spacemango on Tue, 2020-06-09 13:31 |
by spacemango Tue, 2020-06-09 13:42 |
General discussion | ||
|
FOCBOX X is not detected by sumedh on Tue, 2022-09-13 22:16 |
3 |
by frank Mon, 2022-09-19 09:18 |
General discussion | |
|
IMU 9250 and 6050 not working on new vesc 4.12 and 4.20 by trung_qly on Sun, 2021-09-05 16:11 |
3 |
by spatsirk Mon, 2025-06-09 18:55 |
General discussion | |
|
Isolated CANbus / CAN by shener on Wed, 2024-10-23 15:15 |
1 |
by Markula Thu, 2024-10-24 22:19 |
General discussion | |
|
How to reboot VESC from serial port by Ivko on Mon, 2021-01-04 18:44 |
by Ivko Mon, 2021-01-04 18:44 |
General discussion | ||
|
Loud Bang at Sensor-less Switchover with hub motor by hackeybabel on Sat, 2021-08-21 11:13 |
2 |
by hackeybabel Thu, 2021-08-26 07:19 |
General discussion | |
|
Where can I ask technical questions about products? by MrSurly on Tue, 2022-04-19 05:22 |
by MrSurly Tue, 2022-04-19 05:22 |
General discussion | ||
|
Reverse button not working by oangelo on Sat, 2023-02-04 21:47 |
1 |
by oangelo Tue, 2023-02-07 18:16 |
General discussion | |
|
Reverse indicator by bmblank on Wed, 2024-03-20 20:41 |
by bmblank Wed, 2024-03-20 20:41 |
General discussion | ||
|
Kill switch by 999dom999 on Thu, 2022-04-07 10:44 |
7 |
by hnr_engineer Tue, 2022-07-26 06:07 |
General discussion | |
|
What do the LEDs mean? by Chaim Lukas Maier on Thu, 2023-01-19 16:35 |
1 |
by frank Thu, 2023-01-19 18:02 |
General discussion | |
|
being able to connect VESC 6 MK VI with servo by mmobayed on Mon, 2024-03-11 20:22 |
1 |
by Srihari293 Wed, 2024-03-13 08:45 |
General discussion | |
|
Repairing by lamak on Thu, 2025-06-26 07:08 |
2 |
by ispor4en Fri, 2025-06-27 21:15 |
General discussion | |
|
current control mode with duty cycle limit based on throttle by devin on Thu, 2020-01-16 05:45 |
by devin Thu, 2020-01-16 05:49 |
General discussion |
Pages
