You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Completely disabling regen current possibility on vesc by riraheta on Tue, 2022-11-29 01:48 |
3 |
by frank Wed, 2022-11-30 09:33 |
General discussion | |
|
Spin motor at constant ERPM while a button is pressed by t-dub-maui on Fri, 2024-01-26 07:33 |
by t-dub-maui Fri, 2024-01-26 07:33 |
General discussion | ||
|
Need some help on motor config and app config for Flypsky 65161 motor with FSESC75200 75V by freedomBoogie on Thu, 2021-03-04 09:30 |
2 |
by JoeSwe Sun, 2022-05-29 17:26 |
General discussion | |
|
Unofficial VESC Discord server by kubark42 on Tue, 2021-11-16 16:07 |
by kubark42 Fri, 2021-11-19 03:12 |
General discussion | ||
|
LED HW PWM?? by milom on Fri, 2018-11-16 15:29 |
1 |
by benjamin Fri, 2018-11-23 09:57 |
General discussion | |
|
display readings by FatsoBatso on Wed, 2021-02-24 18:01 |
by FatsoBatso Wed, 2021-02-24 18:01 |
General discussion | ||
|
Minimum speed by Davideo on Sat, 2017-10-21 17:40 |
7 |
by Davideo Thu, 2017-12-07 00:18 |
General discussion | |
|
Trying to read and set MCCONF by Jamie42 on Tue, 2020-03-24 19:47 |
by Jamie42 Tue, 2020-03-24 19:47 |
General discussion | ||
|
Disabling speed cutoff by RDN2003 on Sat, 2020-10-24 00:25 |
1 |
by frank Tue, 2020-10-27 16:42 |
General discussion | |
|
controlling 2 motors for two directions each by ori harush on Mon, 2022-06-06 07:17 |
4 |
by Indy8976 Tue, 2022-06-21 13:36 |
General discussion | |
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 on Wed, 2023-04-12 16:28 |
by Tom65 Wed, 2023-04-12 16:28 |
General discussion | ||
|
VESC Battery Packs by frank on Tue, 2020-10-13 15:21 |
7 |
by dethei Mon, 2022-04-04 15:31 |
General discussion | |
|
Custom code changes- I/O pin go high or low by dsuresh on Thu, 2021-05-13 19:50 |
2 |
by dsuresh Fri, 2021-05-14 22:30 |
General discussion | |
|
can not start motor with high duty by qdxiatao on Sat, 2018-03-24 03:58 |
by qdxiatao Sat, 2018-03-24 03:58 |
General discussion | ||
|
VESC - Motor will not start until a small kick is applied from a full stop despite using hall sensors by 010203040506070809 on Wed, 2019-10-23 23:12 |
by 010203040506070809 Wed, 2019-10-23 23:12 |
General discussion | ||
|
vesc tool not giving me the right values by spacemango on Tue, 2020-06-09 13:31 |
by spacemango Tue, 2020-06-09 13:42 |
General discussion | ||
|
FOCBOX X is not detected by sumedh on Tue, 2022-09-13 22:16 |
3 |
by frank Mon, 2022-09-19 09:18 |
General discussion | |
|
IMU 9250 and 6050 not working on new vesc 4.12 and 4.20 by trung_qly on Sun, 2021-09-05 16:11 |
2 |
by skyline1970 Thu, 2022-03-24 20:57 |
General discussion | |
|
How to reboot VESC from serial port by Ivko on Mon, 2021-01-04 18:44 |
by Ivko Mon, 2021-01-04 18:44 |
General discussion | ||
|
Loud Bang at Sensor-less Switchover with hub motor by hackeybabel on Sat, 2021-08-21 11:13 |
2 |
by hackeybabel Thu, 2021-08-26 07:19 |
General discussion |
Pages
