You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Balance App by EVolution EV on Tue, 2019-12-31 05:11 |
by EVolution EV Thu, 2020-01-02 05:55 |
VESC Tool | ||
|
Protecting PSU with resistive load when braking by henxan on Sat, 2019-11-16 21:08 |
8 |
by Stupidspencer Mon, 2019-12-30 18:02 |
General discussion | |
|
motor detection - what to expect when spinning up the motor by grantmoy74 on Sat, 2019-12-28 11:58 |
2 |
by grantmoy74 Sun, 2019-12-29 05:21 |
VESC Tool | |
|
REVERSE FAIL in ADC_CURRENT_REV_BUTTON_BRAKE_ADC by dk-odense on Tue, 2019-12-17 15:45 |
1 |
by benjamin Fri, 2019-12-27 23:09 |
VESC Firmware | |
|
Dual motor setup over CAN with UART by Pawel on Sun, 2018-06-17 11:50 |
5 |
by alex63610 Fri, 2019-12-27 14:27 |
VESC Firmware | |
|
Maker X Mini VESC burned at 46V. My fault or shitty quality? by smileandbeware on Mon, 2019-11-18 10:53 |
3 |
by frank Thu, 2019-12-26 15:27 |
Third Party Hardware | |
|
No brakes in PID Speed Control mode by karololo on Tue, 2019-10-15 11:31 |
3 |
by Gesndrery Thu, 2019-12-26 07:00 |
VESC Tool | |
|
Vesc tool 1.26.. issue with firmware updates? by beetbocks on Tue, 2019-12-17 10:17 |
2 |
by Stupidspencer Wed, 2019-12-25 23:04 |
VESC Tool | |
|
Reset parameters by nidhirao on Mon, 2019-12-23 10:57 |
by nidhirao Mon, 2019-12-23 10:57 |
VESC Tool | ||
|
No reverse after FW update from 3.62 to 3.63 by Stupidspencer on Sun, 2019-12-15 20:34 |
4 |
by Stupidspencer Sun, 2019-12-22 21:57 |
VESC Firmware | |
|
VESC6+ compatible 540 1/10 BLDC motor recommendation by henry10210 on Tue, 2019-12-17 08:15 |
3 |
by benjamin Sun, 2019-12-22 09:56 |
General discussion | |
|
3.64 can_scan breaks with ppm enabled. by fessyfoo on Fri, 2019-12-20 20:40 |
1 |
by fessyfoo Sun, 2019-12-22 03:44 |
VESC Firmware | |
|
VESC recommendation for sailboat conversion by Henque19 on Thu, 2019-11-28 00:42 |
9 |
by Henque19 Fri, 2019-12-20 16:15 |
General discussion | |
|
Two VESCs with servo-out firmware by _saeed_arabi_ on Fri, 2019-12-13 22:22 |
1 |
by frank Thu, 2019-12-19 21:34 |
General discussion | |
|
Position control with Hall and A/B encoder by jo.rauchfuss on Tue, 2019-12-17 04:12 |
4 |
by frank Thu, 2019-12-19 21:09 |
General discussion | |
|
VESC PID by nidhirao on Tue, 2019-12-17 13:56 |
by nidhirao Tue, 2019-12-17 13:56 |
VESC Firmware | ||
|
VESC PID by nidhirao on Tue, 2019-12-17 10:13 |
by nidhirao Tue, 2019-12-17 10:13 |
VESC Tool | ||
|
Motor controller commercial test benches by lopezcontreras on Mon, 2019-12-16 15:31 |
by lopezcontreras Mon, 2019-12-16 15:31 |
Third Party Hardware | ||
|
Synchronizing multiple motors before mechanically locking together by hockinsk on Sun, 2019-10-27 23:15 |
2 |
by Stupidspencer Sun, 2019-12-15 22:50 |
General discussion | |
|
Unity FW updating bricked my 4.12 HW by yuvikal on Thu, 2019-12-12 22:16 |
3 |
by frank Sat, 2019-12-14 20:03 |
VESC Firmware |
Pages
