You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Motor Overheating in FOC by amanpereira1 on Thu, 2022-05-05 16:14 |
2 |
by Nuppen Wed, 2024-02-14 08:14 |
General discussion | |
|
Vesc tool shows wrong voltage by anythingstl on Wed, 2024-02-14 20:06 |
by anythingstl Wed, 2024-02-14 20:06 |
VESC Tool | ||
|
Solved: Cruise Control: Push to Activate; Cancel on BRK or Throttle Touched by vadicus on Wed, 2020-01-08 23:47 |
10 |
by vadicus Sat, 2024-02-17 01:37 |
General discussion | |
|
FSESC 75100 motor problem by anythingstl on Tue, 2024-02-13 17:15 |
by anythingstl Mon, 2024-02-19 19:23 |
General discussion | ||
|
real time data blocks not showing by sander123 on Tue, 2024-02-20 15:47 |
1 |
by sander123 Tue, 2024-02-20 15:48 |
VESC Tool | |
|
PAS + UART by Tukkis on Sun, 2024-02-18 20:34 |
1 |
by vadicus Thu, 2024-02-22 01:46 |
General discussion | |
|
Flipsky 75100 and VEVOR MY1020D - Very jerky by DevelopedBug on Sat, 2022-07-16 19:46 |
6 |
by Trooth Fri, 2024-02-23 01:38 |
General discussion | |
|
How to get Max Torque at start by player107 on Fri, 2023-04-07 09:55 |
4 |
by Trooth Fri, 2024-02-23 06:52 |
VESC Tool | |
|
Controller (VESC 6 based) dont like small motor by matrixgti on Mon, 2024-01-29 21:27 |
by matrixgti Fri, 2024-02-23 15:37 |
General discussion | ||
|
Change sensor voltage on latest VESC 75/300 MK IV by R04 on Sun, 2024-01-28 21:22 |
2 |
by frank Fri, 2024-02-23 15:39 |
VESC Original Hardware | |
|
Initial startup time by rxty on Thu, 2022-06-02 18:38 |
3 |
by sifourquier Sun, 2024-02-25 23:16 |
VESC Firmware | |
|
VESC in R/C car by csicso on Mon, 2024-02-26 21:17 |
by csicso Mon, 2024-02-26 21:17 |
VESC Firmware | ||
|
VESC Flipsky 75100 used in Ryobi RM480e electric riding mower. by Ryobi master on Tue, 2024-02-27 00:20 |
by Ryobi master Tue, 2024-02-27 00:20 |
Projects incorporating VESC technology | ||
|
FAULT_CODE_DRV by Yuna on Tue, 2024-02-27 12:08 |
by Yuna Tue, 2024-02-27 12:08 |
General discussion | ||
|
Stator Saturation Compensation Mode by getinthebag on Tue, 2023-02-07 09:12 |
1 |
by benabelay@gmail.com Tue, 2024-02-27 23:22 |
General discussion | |
|
Firmware Compatibility Issue with Custom 75_300 Based Hardware by kevin458 on Wed, 2024-02-28 19:55 |
1 |
by kevin458 Wed, 2024-02-28 20:36 |
VESC Firmware | |
|
75 V 300 A only reading MOSFET temperature 1 in VESC Tool by ryanbohm on Thu, 2024-02-29 01:00 |
by ryanbohm Thu, 2024-02-29 01:00 |
VESC Original Hardware | ||
|
vesc_tool 6 and vesc 4.12 -> motor setup of small outrunner not working by Gawarmel on Thu, 2024-02-29 14:56 |
by Gawarmel Thu, 2024-02-29 14:56 |
VESC Tool | ||
|
IMPSM Motor and Gearing by baein on Tue, 2022-01-25 11:19 |
5 |
by Rohan_Suresh_babu Sat, 2024-03-02 12:18 |
General discussion | |
|
MTPA by hummina on Tue, 2024-02-20 19:54 |
1 |
by Rohan_Suresh_babu Mon, 2024-03-04 06:21 |
General discussion |
Pages
