You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Motor Controller Recommendations - 84V max - 50A Continuous by dylanu on Thu, 2021-11-11 22:54 |
5 |
by mikael Sat, 2023-09-30 01:46 |
General discussion | |
How to get vesc tool for linux on ubuntu? by vitormhenrique on Tue, 2019-10-22 16:00 |
7 |
by JackGunnarsson Mon, 2023-10-02 13:20 |
VESC Tool | |
Need Your Help with PPM Mapping Remote during Setup by silverglate on Sun, 2019-02-03 05:04 |
32 |
by RCHAL158 Fri, 2023-10-13 10:30 |
Third Party Hardware | |
Regen on fully charged battery: soft high voltage limit by e404 on Wed, 2019-02-20 16:15 |
6 |
by Andy G Fri, 2023-10-13 14:26 |
General discussion | |
FOC for BDC? by SlimSh8y on Thu, 2018-07-12 23:05 |
11 |
by JanneHooo Fri, 2023-10-13 18:20 |
VESC Tool | |
Collection of Burned 100/250 Vesc´s by xenon321 on Thu, 2021-07-01 17:39 |
38 |
by electricfox Wed, 2023-10-18 18:21 |
VESC Original Hardware | |
Weird Inductance measurement by a.dahhak on Wed, 2020-06-03 21:53 |
7 |
by emntz Mon, 2023-10-23 19:17 |
General discussion | |
Starter motor stoping for no apparent reason by Bexy on Wed, 2022-08-03 18:07 |
3 |
by Faheem Wed, 2023-10-25 08:56 |
General discussion | |
Cruise Control Questions by piopi0 on Sat, 2022-09-24 03:56 |
3 |
by vadicus Thu, 2023-10-26 01:16 |
VESC Firmware | |
Native PAS PEDELEC support by shaman on Thu, 2019-07-11 12:20 |
39 |
by Nedko Thu, 2023-10-26 21:21 |
Feature Requests | |
Position issue by Davideo on Tue, 2017-09-19 16:48 |
3 |
by bOneWheel Mon, 2023-10-30 15:07 |
VESC Tool | |
FOC and very low speeds by verbeek on Mon, 2018-07-09 16:17 |
18 |
by Chris Barth Fri, 2023-11-10 04:45 |
General discussion | |
Roll-to-start VESC by dsuresh on Fri, 2021-03-12 21:05 |
4 |
by robertkovax Fri, 2023-11-10 16:57 |
General discussion | |
Gan Fets by transcendStaticMode on Tue, 2020-05-05 05:52 |
12 |
by lizardmech Tue, 2023-11-14 13:35 |
Feature Requests | |
VESC tool and sk8-esc V6 set up shows incorrectcurrent usage by DominykasS on Fri, 2022-09-30 13:54 |
2 |
by Frizzaper Wed, 2023-11-15 04:25 |
VESC Tool | |
PID Speed Control not working in ADC mode by a.smith on Mon, 2022-01-17 13:23 |
7 |
by lonelypanda Wed, 2023-11-15 08:40 |
General discussion | |
Weird behaviour on overcurrent : have to reflash then FOC doesn't work by marc426 on Tue, 2020-01-07 23:58 |
11 |
by Tommynwn Fri, 2023-11-17 15:16 |
VESC Original Hardware | |
Motor wizard settings by ESCam on Thu, 2018-11-08 22:49 |
8 |
by dtp Mon, 2023-11-20 00:49 |
VESC Tool | |
Duty cycle mode with neutral by titoxd10001 on Fri, 2017-09-08 12:04 |
25 |
by nyc Tue, 2023-11-21 05:54 |
Feature Requests | |
VESC Tool 2.06 not working either on windows. by oger on Fri, 2020-05-08 00:11 |
4 |
by kjskjs00 Fri, 2023-11-24 23:18 |
VESC Tool |