You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
PWM on output by ml2311 on Tue, 2021-08-24 14:46 |
5 |
by Flyingtux Wed, 2022-03-30 19:31 |
General discussion | |
Reverse rotation command during forward rotation by nisigundam on Wed, 2018-03-07 09:12 |
5 |
by Josh54 Thu, 2022-09-08 18:08 |
General discussion | |
How to make VESC 4.12 can work with 14S batteries? by Ken_chen on Sat, 2018-04-21 04:39 |
5 |
by Roger Wolff Sun, 2018-05-20 08:36 |
General discussion | |
hall sensor calibration. by Roger Wolff on Mon, 2018-04-16 11:17 |
5 |
by svs Mon, 2018-08-27 13:34 |
General discussion | |
RL test fails by de-bodgery on Wed, 2021-09-29 19:55 |
5 |
by TechAUmNu Tue, 2021-10-26 01:22 |
General discussion | |
Current Control issue VESC4 by yosoufe on Tue, 2018-03-20 09:28 |
5 |
by itchavenag Fri, 2019-09-13 12:06 |
General discussion | |
RC Car BLDC - Hall Effect Timing Angle Calculator by mendez on Mon, 2022-03-14 19:20 |
5 |
by sp3swj Sat, 2022-03-19 11:36 |
General discussion | |
Two Motors on same Shaft by Giga93 on Thu, 2017-12-14 10:12 |
5 |
by ThierryGTLTS Sun, 2017-12-17 13:20 |
General discussion | |
ADC Throttle Voltage Issue by Reichen Schaller on Fri, 2022-05-20 01:02 |
5 |
by Gatze Wed, 2022-05-25 17:10 |
General discussion | |
E-bike set up by Iangamblin on Fri, 2023-03-24 14:02 |
5 |
by Iangamblin Thu, 2023-06-29 17:35 |
General discussion | |
What causes RPM inaccuracy? by bww129 on Thu, 2021-04-22 15:50 |
5 |
by bww129 Tue, 2021-05-11 14:07 |
Third Party Hardware | |
Paypal alternative by sam.vanratt on Sat, 2019-01-05 22:03 |
5 |
by benjamin Mon, 2019-02-18 20:11 |
The VESC-Project | |
SK3 Turnigy 6374 149 / encoder CUI AMT102 => can VESC 4 support position control? by fourchette on Tue, 2019-04-02 23:14 |
5 |
by pf26 Thu, 2019-04-04 11:43 |
General discussion | |
Advice please - VESC6 controller for a specific model aircraft application by aabill on Wed, 2019-11-27 11:31 |
5 |
by frank Sun, 2019-12-01 17:28 |
General discussion | |
Dual brushed motors from 1 R/C stick? by VESC1 on Thu, 2019-01-31 06:19 |
5 |
by sam.vanratt Sun, 2019-02-03 16:30 |
General discussion | |
tips for power design by antonchromjak on Mon, 2021-04-12 18:34 |
5 |
by vadicus Tue, 2021-04-27 03:01 |
Third Party Hardware | |
Dual Motor Setup Wizard Not working 1.08 by captclearleft on Tue, 2019-04-16 01:05 |
5 |
by buggermenot Sat, 2022-05-28 15:11 |
VESC Tool | |
Sudden kick (from motor current cut off?) by darowi on Mon, 2017-10-02 18:56 |
5 |
by darowi Tue, 2020-09-15 12:45 |
General discussion | |
Flipsky VESC 50A by CraigL100 on Fri, 2019-08-30 16:57 |
5 |
by CraigL100 Sat, 2019-09-14 12:10 |
Third Party Hardware | |
VESC safety by alexantosh on Tue, 2021-11-23 15:47 |
5 |
by alexantosh Tue, 2021-12-28 15:10 |
General discussion |