You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Request: Report hall sensor tables. by Roger Wolff on Thu, 2018-05-17 15:28 |
7 |
by Tilman Baumann Mon, 2018-08-06 12:24 |
General discussion | |
|
Problem- Regen tripping out BMS on battery pack by jasontwd on Sun, 2018-07-29 10:10 |
2 |
by jzy1115 Tue, 2018-07-31 06:11 |
General discussion | |
|
Question to get a new Motor Running by speedy on Fri, 2018-07-20 07:59 |
1 |
by frank Fri, 2018-07-20 10:23 |
General discussion | |
|
I have soldered MPU 9150 onto my ESC - How can I confirm that it is working? by delond on Sat, 2018-07-14 15:05 |
2 |
by lock Tue, 2018-07-17 02:26 |
General discussion | |
|
Failure of FOC mode brake by jzy1115 on Sun, 2018-03-25 10:23 |
8 |
by iscle Sun, 2018-07-15 19:19 |
General discussion | |
|
Programming NRF51822 Module with ST-Link v2 by koralle on Wed, 2018-07-11 12:06 |
3 |
by koralle Sun, 2018-07-15 01:28 |
General discussion | |
|
Updating fw by Phill Dixon on Fri, 2018-07-06 19:30 |
1 |
by frank Fri, 2018-07-13 13:19 |
General discussion | |
|
FW Vesc-Tool V0.95 by Meche on Mon, 2018-07-09 21:07 |
1 |
by Meche Wed, 2018-07-11 16:29 |
General discussion | |
|
Overheat by Phill Dixon on Tue, 2018-07-03 19:07 |
1 |
by frank Tue, 2018-07-10 09:51 |
General discussion | |
|
Cruise control by setting RPM over UART by solidgeek on Thu, 2018-02-15 10:56 |
3 |
by Lzx19961014 Thu, 2018-07-05 11:20 |
General discussion | |
|
can't communicate with arduino nrf by m.juan on Mon, 2018-07-02 16:57 |
by m.juan Mon, 2018-07-02 16:57 |
General discussion | ||
|
VESC with Raspberry Pi 3 by Antonio Rodrígu... on Sun, 2018-06-03 18:54 |
9 |
by ShortCircuit Thu, 2018-06-28 15:33 |
General discussion | |
|
Motor only running in reverse by obex_mike on Mon, 2018-06-25 16:25 |
2 |
by frank Tue, 2018-06-26 12:36 |
General discussion | |
|
Vesc tool won't connect vesc to motor by moza1313 on Sat, 2018-06-16 10:25 |
2 |
by frank Tue, 2018-06-26 08:48 |
General discussion | |
|
Raptor 2 by Phill Dixon on Wed, 2018-06-13 18:07 |
1 |
by frank Fri, 2018-06-22 11:35 |
General discussion | |
|
VESC Hardware link broken by jparadie on Mon, 2018-06-18 12:21 |
1 |
by frank Fri, 2018-06-22 11:33 |
General discussion | |
|
Newby RPM question by dirkske on Mon, 2018-06-18 23:00 |
7 |
by dirkske Wed, 2018-06-20 20:45 |
General discussion | |
|
360 Rotation Hall Sensors, would these work through ADC? by portnawake on Thu, 2018-06-07 02:37 |
3 |
by Roger Wolff Fri, 2018-06-15 08:50 |
General discussion | |
|
VESC Error "No firmware response" by Magoroth on Tue, 2018-06-12 15:41 |
1 |
by hexakopter Wed, 2018-06-13 01:12 |
General discussion | |
|
[SOLVED]Motors "blocking totally" when throttling, after running VESC setup. by MaddiQ on Tue, 2018-06-12 21:01 |
by MaddiQ Tue, 2018-06-12 23:36 |
General discussion |
Pages
