You are here
VESC Original Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC 100/250MK issues with output power by martin321 » Tue, 2026-01-13 09:52 |
1 |
by electricfox Tue, 2026-01-13 19:21 |
|
|
VESC 75/300 with 120100 motor for hydraulic pump unit by chundri » Mon, 2022-10-31 12:12 |
1 |
by skyline1970 Thu, 2022-11-24 20:04 |
|
|
Driving two motors with 75/300 by cmarc » Wed, 2019-10-16 17:32 |
1 |
by benjamin Fri, 2019-10-18 10:37 |
|
|
VESC BMS Harmony16 by DanielB » Wed, 2026-03-25 14:47 |
1 |
by electricfox Thu, 2026-03-26 19:25 |
|
|
VESC design specification, manual by velolac » Thu, 2020-01-02 15:54 |
1 |
by velolac Sat, 2020-01-11 00:05 |
|
|
Anyone having issues setting speed limits on their ESCs with the Dash 35B? by fstest » Thu, 2026-04-23 17:40 |
1 |
by electricfox Sun, 2026-04-26 19:48 |
|
|
Different HW versions for V6?! by Marc Pflugmann » Sun, 2018-06-24 13:43 |
1 |
by frank Mon, 2018-06-25 13:01 |
|
|
VESC410 detection failed reason: DRV fault by G.ai » Tue, 2023-11-21 09:16 |
1 |
by G.ai Fri, 2023-11-24 02:49 |
|
|
Using ABI Encoders by danielw » Tue, 2018-10-30 14:33 |
1 |
by danielw Wed, 2018-11-07 15:38 |
|
|
75V 300A VESC Max current and Temperature Rise by RanjithBalu56 » Wed, 2023-12-27 07:11 |
1 |
by TechAUmNu Thu, 2023-12-28 20:21 |
|
|
VESC STR-500 by eptv » Sat, 2024-01-13 07:26 |
1 |
by eptv Sat, 2024-08-31 12:36 |
|
|
Vesc 6.4 has 80A continuous current. Is that battery or motor? by MaxMaker1 » Mon, 2020-03-02 23:35 |
1 |
by velolac Sun, 2020-03-29 17:51 |
|
|
VESC DUET + VESC ABI encoder in HALL Emulation Mode (unabled to setup) by D J Beggs » Fri, 2026-06-12 18:56 |
1 |
by electricfox Sat, 2026-06-13 16:49 |
|
|
75/300 R3 with Original FW 4.2 can't update by nice2cu » Sun, 2020-06-14 17:26 |
1 |
by nice2cu Mon, 2020-06-15 20:41 |
|
|
Independent external power for VESC 6 MK3? by henry10210 » Sun, 2020-08-02 00:27 |
1 |
by thefallen Sun, 2020-08-02 16:11 |
|
|
CAN Commands to control VESC 100/250? by harmander_sihra » Fri, 2021-12-17 01:49 |
1 |
by tecnico.solarboat Mon, 2021-12-27 23:29 |
|
|
Speed Pin from motor into VESC 6+? by dfelz » Tue, 2020-04-07 23:42 |
1 |
by frank Mon, 2020-05-04 14:50 |
|
|
Hooking up two or more motor drivers to the same MCU by darkclaude » Thu, 2019-06-20 10:02 |
2 |
by skyline1970 Wed, 2019-07-31 13:53 |
|
|
Need advice : repair , vesc 4.12, vesc 6.4 or wait ? by frameto » Mon, 2017-11-20 21:57 |
2 |
by frameto Wed, 2017-11-22 22:01 |
|
|
Does Trampa BMS work with multiple VESCs? by kylerlaird » Sun, 2025-04-20 03:57 |
2 |
by kylerlaird Sun, 2025-04-20 15:38 |
|
|
VESC 4.12 - Data loss on power off by da_rul0r » Wed, 2019-08-14 16:43 |
2 |
by da_rul0r Thu, 2019-08-15 08:33 |
|
|
fault_code_high_offset_current_sensor_1 by Enak » Thu, 2019-10-10 02:48 |
2 |
by Enak Fri, 2019-10-11 01:24 |
|
|
HW 4.12 USB Device Descriptor Failed-> Red light flashed on start by MTBVASEY » Wed, 2018-04-04 11:06 |
2 |
by MTBVASEY Wed, 2018-04-04 22:24 |
|
|
VESC 100/250 Bluetooth not showing up by JumpinJackFlash » Sun, 2022-10-09 19:03 |
2 |
by JumpinJackFlash Tue, 2022-10-11 17:27 |
|
|
Vesc motor resistance value by HiandHello » Wed, 2023-02-15 07:45 |
2 |
by HiandHello Wed, 2023-02-15 22:57 |
Log in to post new content in the forum.
