You are here
VESC Original Hardware
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Why Mosfet and Motor HW temp sensor schematic are different?! by ThierryGTLTS » Sat, 2017-09-09 10:13 |
3 |
by ThierryGTLTS Mon, 2017-09-11 12:50 |
|
|
Dual VESC sync problem by Svenska Svenson » Wed, 2017-10-18 18:56 |
4 |
by Svenska Svenson Sat, 2017-10-28 13:47 |
|
|
Dual Vesc6 setup: Vesc with nrf no blue light by Paul15578 » Sat, 2017-11-04 04:00 |
2 |
by Paul15578 Mon, 2017-11-06 13:56 |
|
|
Need advice : repair , vesc 4.12, vesc 6.4 or wait ? by frameto » Mon, 2017-11-20 21:57 |
2 |
by frameto Wed, 2017-11-22 22:01 |
|
|
VESC hardware schematics by cromoly » Tue, 2017-11-28 04:44 |
4 |
by ThierryGTLTS Tue, 2017-12-19 14:03 |
|
|
vesc from flier by Doublewave » Sat, 2017-12-30 10:15 |
1 |
by josh Thu, 2018-01-04 04:32 |
|
|
Spare 5V current for accessories by Pimousse » Mon, 2018-01-08 15:49 |
3 |
by benjamin Wed, 2018-01-24 15:21 |
|
|
Total dead-time of the MOSFETs ???!! by ThierryGTLTS » Tue, 2017-09-12 17:08 |
6 |
by TechAUmNu Fri, 2018-01-26 10:37 |
|
|
Current measuring with DRV amplifiers by PXSS » Mon, 2018-02-12 03:14 |
5 |
by lizardmech Fri, 2018-03-02 00:43 |
|
|
Higher voltage DRV error by jarrow » Tue, 2018-03-06 10:06 |
0 |
by jarrow Tue, 2018-03-06 10:06 |
|
|
Hall count drift by xachmo » Mon, 2018-03-26 07:17 |
2 |
by xachmo Wed, 2018-03-28 21:26 |
|
|
HW 4.12 USB Device Descriptor Failed-> Red light flashed on start by MTBVASEY » Wed, 2018-04-04 11:06 |
2 |
by MTBVASEY Wed, 2018-04-04 22:24 |
|
|
How to wire Cruise Control with VESC6 ADC by Tilman Baumann » Tue, 2018-04-10 11:11 |
0 |
by Tilman Baumann Tue, 2018-04-10 11:11 |
|
|
DRV8302 Gate drive limitations by nickw1881 » Sun, 2018-04-29 09:56 |
0 |
by nickw1881 Sun, 2018-04-29 09:56 |
|
|
Mechanical dimensions of VESC 6 by ufechner » Sat, 2018-04-28 19:01 |
2 |
by TechAUmNu Mon, 2018-04-30 22:28 |
|
|
HARDWARE QUESTION: Maximum AC voltage VESC can tolerate? by danvel » Fri, 2018-04-27 15:31 |
4 |
by Roger Wolff Mon, 2018-05-14 22:13 |
|
|
Vesc4 have 2 Analog output pins? by greensightag.com » Sat, 2018-05-12 00:42 |
1 |
by Roger Wolff Tue, 2018-05-15 10:51 |
|
|
Input Voltage on PPM (Servo) VESC6? by Marc Pflugmann » Fri, 2018-05-25 21:02 |
3 |
by Roger Wolff Thu, 2018-05-31 08:05 |
|
|
VESC 6.4 supplys Arduino over SIGNAL!! by MaxMaker1 » Thu, 2018-05-24 15:02 |
4 |
by frank Mon, 2018-06-04 23:24 |
|
|
Different HW versions for V6?! by Marc Pflugmann » Sun, 2018-06-24 13:43 |
1 |
by frank Mon, 2018-06-25 13:01 |
|
|
Adding capacitors with long power cables? by rich » Thu, 2017-09-07 20:40 |
6 |
by frank Mon, 2018-08-20 09:12 |
|
|
HW 4.12 Change low voltage cutoff by subodh.malgonde » Tue, 2018-09-18 07:31 |
7 |
by TheFallen Thu, 2018-09-20 09:51 |
|
|
Using ABI Encoders by danielw » Tue, 2018-10-30 14:33 |
1 |
by danielw Wed, 2018-11-07 15:38 |
|
|
Flashing via SWD works, but no green LED or USB enumeration by vpl » Fri, 2018-11-16 17:48 |
1 |
by vpl Wed, 2018-11-21 17:27 |
|
|
VESC on 48V 1500W HUB motor by jordanlow » Sat, 2019-01-12 14:52 |
4 |
by jordanlow Thu, 2019-01-24 04:14 |
Log in to post new content in the forum.
