You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter![]() |
Replies | Last post | |
---|---|---|---|
foc detection params by stefann » Mon, 2020-04-13 00:07 |
0 |
by stefann Mon, 2020-04-13 00:28 |
|
FOC detection.... by Roger Wolff » Thu, 2018-05-24 17:37 |
3 |
by TechAUmNu Sun, 2018-05-27 21:14 |
|
FOC Encoder autotune issue by David_Lo » Tue, 2020-01-21 11:54 |
0 |
by David_Lo Tue, 2020-01-21 11:54 |
|
FOC for BDC? by SlimSh8y » Thu, 2018-07-12 23:05 |
10 |
by frank Fri, 2018-07-20 10:41 |
|
FOC Motor Detection Values Incorrect, PID Tuning Advice? by bmwman91 » Mon, 2020-07-06 03:09 |
0 |
by bmwman91 Mon, 2020-07-06 03:21 |
|
foc openloop not starting motor on higher erpm by Alan oldguy » Thu, 2018-09-06 08:43 |
8 |
by technicc Mon, 2022-03-28 09:23 |
|
FOC with 2 Poles and only 6 Windings? by martin2day » Fri, 2020-07-17 08:16 |
2 |
by martin2day Sat, 2020-07-18 10:36 |
|
Freewheeling by Stianaj » Fri, 2020-01-17 19:15 |
0 |
by Stianaj Fri, 2020-01-17 19:15 |
|
From where can I access the FOC code? by vimi94 » Mon, 2019-07-01 14:36 |
1 |
by Teslafly Sat, 2019-07-20 10:31 |
|
fsesc 4.20 CAN bus not detecting by LeonD » Sat, 2021-05-08 15:44 |
3 |
by MartyMcFlyFord Sat, 2022-06-04 16:54 |
|
FSESC 6.6 200A Unable to send signal to slave VESC by bms368 » Sat, 2021-02-20 06:16 |
1 |
by adidasgoogle Sun, 2021-03-07 19:11 |
|
Full Brake vs Switch Off by meisterpro » Mon, 2021-03-22 14:36 |
0 |
by meisterpro Mon, 2021-03-22 14:36 |
|
Get data from VESC on Arduino by jhanvisharma » Wed, 2021-04-07 08:25 |
1 |
by CTSchorsch Wed, 2021-04-07 09:05 |
|
getting started by SilkyD » Mon, 2021-10-25 12:49 |
0 |
by SilkyD Mon, 2021-10-25 12:49 |
|
GPDrive details? by shaman » Wed, 2020-03-11 19:05 |
1 |
by s0313045 Fri, 2021-02-05 08:34 |
|
Half FSESC6.6 not working through can-bus by sergio » Sat, 2019-09-21 17:03 |
8 |
by bjorn westen Thu, 2021-06-10 08:37 |
|
Hall sensor problems by Traceo » Wed, 2021-11-10 00:05 |
2 |
by Traceo Fri, 2021-11-19 22:35 |
|
Help needed for VESC set up! by mbagrey » Wed, 2018-09-19 22:07 |
3 |
by Roger Wolff Sun, 2018-09-30 16:15 |
|
Help setting up dual vesc via CANBUS by Jaystro16 » Sun, 2019-08-04 01:39 |
1 |
by frank Wed, 2019-08-14 13:55 |
|
Help with a settings for only generator by Mafo » Fri, 2018-03-02 16:59 |
7 |
by JP Thu, 2022-03-24 18:31 |
|
help with vesc real time data trouble shooting by stefann » Wed, 2020-04-08 23:02 |
0 |
by stefann Wed, 2020-04-08 23:02 |
|
help with vesc real time data trouble shooting by stefann » Wed, 2020-04-08 23:03 |
0 |
by stefann Wed, 2020-04-08 23:03 |
|
High Current Sampling Mode True 80% current by antonchromjak » Sun, 2017-09-24 21:14 |
2 |
by antonchromjak Wed, 2017-09-27 19:59 |
|
Hoverboard motor Reverse direction by Silvio Semedo » Sat, 2021-01-16 17:43 |
1 |
by skyline1970 Sun, 2021-02-07 17:32 |
|
Hoverboard Motor Setup by CadillacF1 » Sat, 2020-07-11 05:26 |
2 |
by TheFallen Mon, 2020-08-17 12:14 |
Log in to post new content in the forum.
