You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Detection for a drone outrunner 515 kV and 775 kV by MaksK » Thu, 2020-06-04 16:05 |
0 |
by MaksK Thu, 2020-06-04 16:05 |
|
|
Determining Motor and Battery Current Max by technique » Tue, 2020-07-14 15:03 |
1 |
by probie Wed, 2020-08-26 22:01 |
|
|
Dev Tools (Scripting) by curt » Mon, 2022-08-22 15:16 |
0 |
by curt Mon, 2022-08-22 15:16 |
|
|
Did I lock myself out of bluetooth connection? by tylerskate » Sat, 2021-05-29 07:18 |
1 |
by Anordil Thu, 2021-08-05 00:06 |
|
|
Difference between regular and 'setup' values in logged csv by aUser » Tue, 2024-04-23 14:03 |
0 |
by aUser Tue, 2024-04-23 14:03 |
|
|
Different rpm when using 3 vesc with can-bus by ewakegermanyhq » Wed, 2022-08-03 17:03 |
0 |
by ewakegermanyhq Wed, 2022-08-03 17:03 |
|
|
Disable bluetooth. by Roger Wolff » Sun, 2018-10-07 17:06 |
1 |
by arvidb Sun, 2018-10-07 17:27 |
|
|
Discrepancies between VESC Tool 3.01 Motor Settings & XML config file by j.konrad » Sat, 2022-01-15 22:13 |
3 |
by benjamin Mon, 2022-02-21 22:17 |
|
|
Docker images for vesc build? by dammfine » Thu, 2020-04-23 18:56 |
4 |
by brycej Fri, 2020-07-24 18:06 |
|
|
Download latest VESC Tool version by consti » Wed, 2022-06-15 17:24 |
1 |
by frank Thu, 2022-06-16 10:19 |
|
|
Driving Alternator wired as BLDC motor with VESC6 by LittleTinker » Thu, 2019-10-10 13:06 |
6 |
by flyingbrike Wed, 2021-09-22 20:16 |
|
|
Dual Motor Setup not working via CAN Bus (solved) by acleon » Fri, 2020-06-19 00:03 |
0 |
by acleon Fri, 2020-06-19 16:33 |
|
|
Dual Motor Setup Wizard Not working 1.08 by captclearleft » Tue, 2019-04-16 01:05 |
5 |
by buggermenot Sat, 2022-05-28 15:11 |
|
|
duty cicle 95% but current not at max by rodrigo.baronio » Mon, 2023-02-06 15:52 |
0 |
by rodrigo.baronio Mon, 2023-02-06 15:52 |
|
|
Duty Cycle Acceleration Limit by jfaille » Tue, 2020-06-16 23:17 |
3 |
by amaussa Sun, 2020-09-13 12:59 |
|
|
Duty Cycle Mode - limited ZERO RPM duty cycle by maheshK » Mon, 2021-11-29 11:24 |
2 |
by frank Tue, 2021-11-30 07:46 |
|
|
ennoid bms by roqm » Fri, 2020-10-30 18:22 |
0 |
by roqm Fri, 2020-10-30 18:22 |
|
|
Erpm / torque setting with remote control, Vesc wand by Lasse » Fri, 2021-02-05 22:41 |
1 |
by skyline1970 Tue, 2021-02-09 20:03 |
|
|
ERPM scaling / Maximum motor speed / RPM by Azza » Tue, 2019-09-03 17:16 |
1 |
by Azza Fri, 2019-09-06 18:20 |
|
|
Error on log-file recording: Could not get Positioning Working by hpb66 » Mon, 2022-05-23 08:23 |
0 |
by hpb66 Mon, 2022-05-23 08:23 |
|
|
ESC State, Switch Value, and Motor Position unknown by 175_pilot » Wed, 2020-11-04 04:22 |
0 |
by 175_pilot Wed, 2020-11-04 04:22 |
|
|
experiment tab rpm ramp up and dual separate motor control by tobiokanobi » Thu, 2022-04-14 20:20 |
5 |
by tobiokanobi Tue, 2022-04-26 15:32 |
|
|
Extremely slow FW update (Vesc Tool 2.2) by fender90 » Mon, 2020-02-03 19:26 |
0 |
by fender90 Wed, 2020-02-05 05:22 |
|
|
FAILED DETCTION. REASON:-11,and FAULT_CODE_DRV by marco esteban l... » Wed, 2019-12-11 01:40 |
2 |
by marco esteban l... Wed, 2019-12-11 18:54 |
|
|
Failure to download VESC Tool by CallumMac » Tue, 2022-01-25 02:38 |
26 |
by Ian Watts Wed, 2022-03-16 12:25 |
Log in to post new content in the forum.
