You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
FlipSky VESC 4.12 FW 3.62 BATTERY_TYPE_LIION_3__4_2 by bldcfreek » Thu, 2019-12-05 16:48 |
1 |
by frank Wed, 2019-12-11 14:50 |
|
|
Flipsky nrf51288 by Idoff » Tue, 2018-12-11 21:33 |
2 |
by frank Mon, 2019-02-18 09:00 |
|
|
Flipsky can't connect to vesc tool by vescbeginer » Fri, 2024-08-02 20:16 |
3 |
by wimleo Wed, 2025-03-19 17:49 |
|
|
Flipsky 75100foc motor detection sensor issue fails every crysaltemotor I've tried by Wheelzscootersinc » Fri, 2023-02-03 21:36 |
1 |
by tom355 Sun, 2023-02-05 11:11 |
|
|
Flipsky 6.6 and VESC 5.3 don't mix? by Miniproto » Sun, 2022-11-27 16:34 |
0 |
by Miniproto Sun, 2022-11-27 16:34 |
|
|
FIXED: VESC Express Wifi or Bluetooth connection to VESC Tool: not showing up? by steveeng » Mon, 2025-02-03 22:37 |
6 |
by steveeng Sat, 2025-02-08 19:22 |
|
|
Firmware update failing (from V3.38 to V6) by Amaxophobie » Wed, 2024-06-05 14:58 |
1 |
by tokerodev Tue, 2024-07-09 19:19 |
|
|
Firmware issues by salvasalce » Tue, 2022-12-13 16:12 |
2 |
by Lennart Duijn Mon, 2023-01-09 22:10 |
|
|
Firmware 5.2 how to Fast start¡¡¡ by Oscar Lozano Gimenez » Tue, 2021-02-23 10:00 |
1 |
by skyline1970 Fri, 2021-02-26 15:09 |
|
|
FFT in VESC Tool by RSR » Thu, 2018-05-31 14:37 |
3 |
by TechAUmNu Thu, 2018-05-31 16:28 |
|
|
Feature request: Raw hall data. by Roger Wolff » Mon, 2018-06-11 15:49 |
4 |
by blubbi321 Tue, 2022-03-29 16:32 |
|
|
FAULT_CODE_UNDER_VOLTAGE by alexantosh » Mon, 2021-11-29 09:26 |
9 |
by heravinluca Thu, 2022-08-04 04:19 |
|
|
Fault Codes by Joe_Lowtech » Wed, 2019-02-13 20:06 |
2 |
by mthielvoldt Thu, 2019-07-18 00:38 |
|
|
Failure to download VESC Tool by CallumMac » Tue, 2022-01-25 02:38 |
26 |
by Ian Watts Wed, 2022-03-16 12:25 |
|
|
FAILED DETCTION. REASON:-11,and FAULT_CODE_DRV by marco esteban l... » Wed, 2019-12-11 01:40 |
2 |
by marco esteban l... Wed, 2019-12-11 18:54 |
|
|
Extremely slow FW update (Vesc Tool 2.2) by fender90 » Mon, 2020-02-03 19:26 |
0 |
by fender90 Wed, 2020-02-05 05:22 |
|
|
Expert VESC programmer wanted by SGi » Mon, 2023-10-23 01:59 |
1 |
by electricfox Mon, 2023-10-23 09:12 |
|
|
experiment tab rpm ramp up and dual separate motor control by tobiokanobi » Thu, 2022-04-14 20:20 |
5 |
by tobiokanobi Tue, 2022-04-26 15:32 |
|
|
ESC State, Switch Value, and Motor Position unknown by 175_pilot » Wed, 2020-11-04 04:22 |
0 |
by 175_pilot Wed, 2020-11-04 04:22 |
|
|
Error on log-file recording: Could not get Positioning Working by hpb66 » Mon, 2022-05-23 08:23 |
0 |
by hpb66 Mon, 2022-05-23 08:23 |
|
|
Error creating appimage by EduardoHP28 » Fri, 2025-02-21 07:35 |
0 |
by EduardoHP28 Fri, 2025-02-21 07:37 |
|
|
ERPM, the RPM on the motor does not change by hopeingod » Fri, 2024-05-10 11:15 |
6 |
by hopeingod Mon, 2024-05-13 20:45 |
|
|
ERPM scaling / Maximum motor speed / RPM by Azza » Tue, 2019-09-03 17:16 |
1 |
by Azza Fri, 2019-09-06 18:20 |
|
|
Erpm / torque setting with remote control, Vesc wand by Lasse » Fri, 2021-02-05 22:41 |
1 |
by skyline1970 Tue, 2021-02-09 20:03 |
|
|
ennoid bms by roqm » Fri, 2020-10-30 18:22 |
0 |
by roqm Fri, 2020-10-30 18:22 |
Log in to post new content in the forum.
