You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Speed control by dent » Tue, 2020-03-10 20:11 |
2 |
by dent Wed, 2020-03-11 02:49 |
|
|
Can't update the VESC firmware by mansolander » Thu, 2020-03-05 11:30 |
1 |
by mansolander Fri, 2020-03-06 11:24 |
|
|
New version. by ThierryGTLTS » Thu, 2017-09-07 19:22 |
6 |
by Hectortcher Wed, 2020-03-04 11:21 |
|
|
Reconstruct detection control algorithm inside the tool by kaanozgen » Wed, 2020-02-26 18:50 |
0 |
by kaanozgen Wed, 2020-02-26 18:50 |
|
|
VESC Tool Compatible With FW 3.34 by a.ceviker » Sun, 2018-07-29 11:38 |
9 |
by bitmixer Fri, 2020-02-21 22:18 |
|
|
Input Setup Wizard - Update Firmware by pmg » Thu, 2020-02-13 09:54 |
0 |
by pmg Thu, 2020-02-13 09:54 |
|
|
Extremely slow FW update (Vesc Tool 2.2) by fender90 » Mon, 2020-02-03 19:26 |
0 |
by fender90 Wed, 2020-02-05 05:22 |
|
|
VESC tool max current by marcus.herold » Wed, 2020-01-29 19:30 |
3 |
by marcus.herold Thu, 2020-01-30 16:26 |
|
|
PPM mapping not working by Andytttt » Thu, 2020-01-09 05:58 |
1 |
by frank Mon, 2020-01-27 21:06 |
|
|
PPM Configuration is Only Working While Connected to VESC Software by kyle45 » Wed, 2020-01-15 05:13 |
2 |
by frank Mon, 2020-01-27 21:03 |
|
|
Missing Braking Power in ADC by Silverline » Wed, 2019-06-12 19:48 |
8 |
by positiv Fri, 2020-01-24 14:07 |
|
|
FOC Encoder autotune issue by David_Lo » Tue, 2020-01-21 11:54 |
0 |
by David_Lo Tue, 2020-01-21 11:54 |
|
|
Freewheeling by Stianaj » Fri, 2020-01-17 19:15 |
0 |
by Stianaj Fri, 2020-01-17 19:15 |
|
|
VESC tool load empty by arminoonk » Thu, 2020-01-16 14:51 |
0 |
by arminoonk Thu, 2020-01-16 14:51 |
|
|
supported firmware by velolac » Mon, 2020-01-13 22:55 |
3 |
by velolac Tue, 2020-01-14 21:47 |
|
|
arrow key hot working (neither on the app) but the board works correclty by lorenzidomenico94 » Tue, 2020-01-14 11:30 |
0 |
by lorenzidomenico94 Tue, 2020-01-14 11:30 |
|
|
Adding HM-10 Compatibility with Small Changes to Code by Jfriesen » Sat, 2018-06-09 00:45 |
5 |
by CTSchorsch Mon, 2020-01-06 07:11 |
|
|
Balance App by EVolution EV » Tue, 2019-12-31 05:11 |
0 |
by EVolution EV Thu, 2020-01-02 05:55 |
|
|
motor detection - what to expect when spinning up the motor by grantmoy74 » Sat, 2019-12-28 11:58 |
2 |
by grantmoy74 Sun, 2019-12-29 05:21 |
|
|
No brakes in PID Speed Control mode by karololo » Tue, 2019-10-15 11:31 |
3 |
by Gesndrery Thu, 2019-12-26 07:00 |
|
|
Vesc tool 1.26.. issue with firmware updates? by beetbocks » Tue, 2019-12-17 10:17 |
2 |
by Stupidspencer Wed, 2019-12-25 23:04 |
|
|
Reset parameters by nidhirao » Mon, 2019-12-23 10:57 |
0 |
by nidhirao Mon, 2019-12-23 10:57 |
|
|
VESC PID by nidhirao » Tue, 2019-12-17 10:13 |
0 |
by nidhirao Tue, 2019-12-17 10:13 |
|
|
FAILED DETCTION. REASON:-11,and FAULT_CODE_DRV by marco esteban l... » Wed, 2019-12-11 01:40 |
2 |
by marco esteban l... Wed, 2019-12-11 18:54 |
|
|
BUG - RAMPING on VESC TOOL? by Filcas » Tue, 2019-12-10 19:29 |
2 |
by Filcas Wed, 2019-12-11 17:15 |
Log in to post new content in the forum.
