You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Flipsky nrf51288 by Idoff » Tue, 2018-12-11 21:33 |
2 |
by frank Mon, 2019-02-18 09:00 |
|
|
Is there a complete documentation for the communication protocol between the vesc tool and the board? by aishangmu » Tue, 2018-12-25 09:00 |
2 |
by Caustic_Zinc Fri, 2019-02-08 19:27 |
|
|
Autodetection algorithm by Griffen » Thu, 2019-01-03 18:44 |
2 |
by Gmack Fri, 2020-09-18 16:39 |
|
|
cant connect via usb by curtm » Wed, 2019-06-19 03:05 |
2 |
by curtm Thu, 2019-07-04 00:37 |
|
|
Fault Codes by Joe_Lowtech » Wed, 2019-02-13 20:06 |
2 |
by mthielvoldt Thu, 2019-07-18 00:38 |
|
|
Advanced settings for FOC motor detection (flux linkage) by jaghori.sasan » Sun, 2019-02-17 09:34 |
2 |
by jaghori.sasan Sun, 2019-02-17 17:51 |
|
|
Setup for very slow < 100RPM on Maytech 6365 Motor. by jason3w » Tue, 2020-09-01 10:52 |
2 |
by asapereira Mon, 2020-09-14 10:26 |
|
|
VESC Tool Platinum : Windows 7 - Not working by moorem » Mon, 2020-05-18 23:19 |
2 |
by TheFallen Tue, 2020-12-15 12:06 |
|
|
Android environment. by ka_ru » Tue, 2020-10-20 13:47 |
2 |
by ka_ru Wed, 2020-10-21 10:54 |
|
|
Hoverboard Motor Setup by CadillacF1 » Sat, 2020-07-11 05:26 |
2 |
by TheFallen Mon, 2020-08-17 12:14 |
|
|
FOC with 2 Poles and only 6 Windings? by martin2day » Fri, 2020-07-17 08:16 |
2 |
by martin2day Sat, 2020-07-18 10:36 |
|
|
48v problems by vufmihai » Wed, 2020-07-22 22:53 |
2 |
by vufmihai Fri, 2020-07-31 07:25 |
|
|
More detail in tool tips by TechAUmNu » Mon, 2018-07-23 20:15 |
2 |
by TechAUmNu Tue, 2018-07-24 13:52 |
|
|
Firmware issues by salvasalce » Tue, 2022-12-13 16:12 |
2 |
by Lennart Duijn Mon, 2023-01-09 22:10 |
|
|
Motor setup help please by TrevM » Wed, 2017-12-13 17:11 |
2 |
by nickw1881 Wed, 2018-03-21 05:42 |
|
|
Installing VESC Tool on Jetson Nano by mrburns19 » Tue, 2023-02-07 04:54 |
2 |
by mrburns19 Sun, 2023-02-12 01:44 |
|
|
Update 0.87 impossible by vpower » Thu, 2018-01-18 13:17 |
2 |
by arvidb Thu, 2018-01-18 17:07 |
|
|
Vesctool otg by meashman » Sat, 2022-08-06 10:05 |
2 |
by meashman Wed, 2022-08-17 06:39 |
|
|
ADC Connector is very touchy by ebikerevolution » Wed, 2018-05-09 20:30 |
2 |
by TechAUmNu Tue, 2018-05-15 10:46 |
|
|
VESC tool and sk8-esc V6 set up shows incorrectcurrent usage by DominykasS » Fri, 2022-09-30 13:54 |
2 |
by Frizzaper Wed, 2023-11-15 04:25 |
|
|
High Current Sampling Mode True 80% current by antonchromjak » Sun, 2017-09-24 21:14 |
2 |
by antonchromjak Wed, 2017-09-27 19:59 |
|
|
Software safety features interrupting normal operation. by Tsomo » Wed, 2021-07-14 01:29 |
2 |
by Tsomo Wed, 2021-07-14 01:32 |
|
|
current control via CAN not working by STTS » Thu, 2021-08-12 11:51 |
2 |
by mm_iem Mon, 2021-08-30 18:00 |
|
|
Question about FOC Wizard by proget.snc » Thu, 2021-08-26 16:31 |
2 |
by proget.snc Thu, 2021-09-02 14:23 |
|
|
Motor whine with HFI? by christopher.h.poole » Mon, 2021-04-19 15:49 |
2 |
by christopher.h.poole Tue, 2021-06-15 21:18 |
Log in to post new content in the forum.
