You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
How to start with vesc source code ? by cmarc » Tue, 2020-01-28 15:48 |
0 |
by cmarc Tue, 2020-01-28 15:48 |
|
|
How trottle input by wire? by Heimfried » Mon, 2020-01-27 17:49 |
2 |
by Heimfried Mon, 2020-01-27 21:43 |
|
|
How to connect MPU6050 breakout board to VESC 4.12 by klucznik » Sun, 2020-01-26 19:11 |
1 |
by klucznik Sun, 2020-01-26 22:06 |
|
|
Help with FOC/PID parameter by CTSchorsch » Thu, 2020-01-23 21:57 |
0 |
by CTSchorsch Thu, 2020-01-23 21:57 |
|
|
VESC apps by bosko » Thu, 2020-01-23 18:28 |
0 |
by bosko Thu, 2020-01-23 18:28 |
|
|
Noob: Enabling VESC 6 MKIII switch and hibernate by adamchicago » Thu, 2020-01-16 16:34 |
2 |
by adamchicago Thu, 2020-01-23 16:52 |
|
|
Access the Vesc terminal using another App (Putty?) by mikej_w » Fri, 2020-01-17 02:23 |
3 |
by vadicus Tue, 2020-01-21 02:19 |
|
|
Vesc_tool running error by kwlimm » Sun, 2020-01-19 10:01 |
0 |
by kwlimm Sun, 2020-01-19 10:01 |
|
|
Push FW .bin File to Controller by vadicus » Wed, 2020-01-15 20:23 |
2 |
by vadicus Thu, 2020-01-16 17:35 |
|
|
Alternator custom VESC hardware: Looking for collaborators by jon@ifold » Wed, 2020-01-15 20:11 |
1 |
by frank Thu, 2020-01-16 16:32 |
|
|
custom firmware by vufmihai » Thu, 2020-01-16 09:06 |
0 |
by vufmihai Thu, 2020-01-16 09:06 |
|
|
current control mode with duty cycle limit based on throttle by devin » Thu, 2020-01-16 05:45 |
0 |
by devin Thu, 2020-01-16 05:49 |
|
|
Noob: clever/stupid mild hybrid idea by robin lawrie » Mon, 2019-10-28 13:44 |
2 |
by vadicus Wed, 2020-01-15 23:33 |
|
|
highest battery current with 6.6? by devin » Tue, 2020-01-14 16:05 |
9 |
by devin Wed, 2020-01-15 01:05 |
|
|
Custom application and UART by Dennis Freiburg » Sat, 2020-01-11 13:19 |
3 |
by Dennis Freiburg Sun, 2020-01-12 19:37 |
|
|
Few questions by ElectroMagneto » Thu, 2020-01-09 23:57 |
10 |
by ElectroMagneto Sat, 2020-01-11 00:45 |
|
|
No inbuilt NRF in vesc6 mkIII from Trampa: feel cheated, paid 300 pounds including customs by PREETHAMKS » Thu, 2020-01-09 15:36 |
1 |
by PREETHAMKS Thu, 2020-01-09 16:10 |
|
|
Up dating firmware by rossco1959 » Mon, 2020-01-06 03:44 |
3 |
by rossco1959 Wed, 2020-01-08 02:06 |
|
|
UART Accel/Gyro/Mag data by NATUITION » Sat, 2019-12-28 11:25 |
3 |
by NATUITION Tue, 2020-01-07 22:14 |
|
|
How to set up RF receiver for PPM or UART input? by adamdorr » Tue, 2020-01-07 16:23 |
0 |
by adamdorr Tue, 2020-01-07 16:23 |
|
|
Accessing the status LEDs by hrucker009 » Sun, 2020-01-05 20:09 |
1 |
by frank Tue, 2020-01-07 09:08 |
|
|
Help calibrating a hub motor by Tin_Man_0 » Thu, 2019-12-26 01:17 |
5 |
by vadicus Tue, 2020-01-07 00:48 |
|
|
Protecting PSU with resistive load when braking by henxan » Sat, 2019-11-16 21:08 |
8 |
by Stupidspencer Mon, 2019-12-30 18:02 |
|
|
VESC6+ compatible 540 1/10 BLDC motor recommendation by henry10210 » Tue, 2019-12-17 08:15 |
3 |
by benjamin Sun, 2019-12-22 09:56 |
|
|
VESC recommendation for sailboat conversion by Henque19 » Thu, 2019-11-28 00:42 |
9 |
by Henque19 Fri, 2019-12-20 16:15 |
Log in to post new content in the forum.
