You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
2kW motor with VESS 75200 by Sazabi » Fri, 2024-04-05 11:17 |
0 |
by Sazabi Fri, 2024-04-05 11:18 |
|
|
DRV8302 Gate Pin output waveform is abnormal by yandongyu1998 » Fri, 2019-12-13 07:21 |
0 |
by yandongyu1998 Fri, 2019-12-13 07:21 |
|
|
Dutycyle dropping under load by Julzz112 » Sun, 2024-04-14 18:31 |
0 |
by Julzz112 Tue, 2024-04-16 08:26 |
|
|
FSESC 75100 motor problem by anythingstl » Tue, 2024-02-13 17:15 |
0 |
by anythingstl Mon, 2024-02-19 19:23 |
|
|
Noob here by Nothanks » Sat, 2024-04-20 01:21 |
0 |
by Nothanks Sat, 2024-04-20 01:21 |
|
|
20S by ahanktcd » Thu, 2024-04-25 14:51 |
0 |
by ahanktcd Thu, 2024-04-25 14:51 |
|
|
Any issues with the DRV8323? by shaman » Thu, 2019-10-24 21:50 |
0 |
by shaman Thu, 2019-10-24 21:50 |
|
|
FAULT_CODE_DRV by Yuna » Tue, 2024-02-27 12:08 |
0 |
by Yuna Tue, 2024-02-27 12:08 |
|
|
G60 motor hall wires pinout by Talonkid119 » Wed, 2024-03-06 03:43 |
0 |
by Talonkid119 Wed, 2024-03-06 03:43 |
|
|
How to set up RF receiver for PPM or UART input? by adamdorr » Tue, 2020-01-07 16:23 |
0 |
by adamdorr Tue, 2020-01-07 16:23 |
|
|
optimizing ebike - vesc 75300 by stealth13 » Fri, 2024-05-03 01:28 |
0 |
by stealth13 Fri, 2024-05-03 01:28 |
|
|
Setting the motor parameters by Lenar » Sat, 2024-05-04 10:18 |
0 |
by Lenar Sat, 2024-05-04 10:18 |
|
|
Battery percentage mapping by Sharkboy » Mon, 2024-05-06 22:55 |
0 |
by Sharkboy Mon, 2024-05-06 22:55 |
|
|
Runtime motor control with CAN by Davidepolpi91 » Fri, 2024-03-15 15:12 |
0 |
by Davidepolpi91 Fri, 2024-03-15 15:12 |
|
|
Vesc WS2812b led issues & support by Ash » Tue, 2019-11-12 08:40 |
0 |
by Ash Tue, 2019-11-12 14:13 |
|
|
About How to control the "FLIPSKY Dual FSESC6.7 PLUS" by tonyH » Tue, 2025-10-14 11:35 |
0 |
by tonyH Tue, 2025-10-14 11:35 |
|
|
Vesc help by Roy Voroncovs » Sat, 2026-05-30 11:34 |
0 |
by Roy Voroncovs Sat, 2026-05-30 11:34 |
|
|
VESC custom firmware custom UART message by steveyplst » Tue, 2020-08-04 10:23 |
0 |
by steveyplst Tue, 2020-08-04 10:23 |
|
|
VESC with asynchronous motors by afbbfa » Fri, 2022-07-29 22:51 |
0 |
by afbbfa Fri, 2022-07-29 22:51 |
|
|
I need clarification on connecting a Magura 0-5k Ohm Pot Twist Throttle to Tronic 250 VESC. by notahorse » Fri, 2022-06-03 08:13 |
0 |
by notahorse Fri, 2022-06-03 08:13 |
|
|
FOC ABS_OVER_CURRENT at high RPM by Philippe Larouche » Sat, 2026-06-06 18:24 |
0 |
by Philippe Larouche Sat, 2026-06-06 18:24 |
|
|
Hall sensor port repeatedly fried on original hardware by Rc 44 » Fri, 2025-10-24 22:44 |
0 |
by Rc 44 Fri, 2025-10-24 22:44 |
|
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 » Mon, 2022-08-01 18:08 |
0 |
by moose09876 Mon, 2022-08-01 18:08 |
|
|
VESC as generator - settings confirmation by justinlsquire » Mon, 2022-06-06 02:44 |
0 |
by justinlsquire Mon, 2022-06-06 02:44 |
|
|
tutorial for hfi by TONY61 » Mon, 2026-06-15 17:11 |
0 |
by TONY61 Mon, 2026-06-15 17:11 |
Log in to post new content in the forum.
