You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Current became not stable over time by AnthonyFR » Mon, 2022-07-25 23:21 |
1 |
by frank Wed, 2022-07-27 20:35 |
|
|
Current control and duty cycle issues. by ESCam » Tue, 2019-04-02 22:55 |
0 |
by ESCam Tue, 2019-04-02 22:55 |
|
|
Current Control issue VESC4 by yosoufe » Tue, 2018-03-20 09:28 |
5 |
by itchavenag Fri, 2019-09-13 12:06 |
|
|
current control mode with duty cycle limit based on throttle by devin » Thu, 2020-01-16 05:45 |
0 |
by devin Thu, 2020-01-16 05:49 |
|
|
Current control performance & best way to tune Kp and Ki by jinwonchung » Thu, 2024-10-17 15:52 |
0 |
by jinwonchung Thu, 2024-10-17 15:53 |
|
|
Current controller issue - Glitches at low current, low RPM by GijsB » Sun, 2022-10-30 12:59 |
1 |
by GijsB Sun, 2022-10-30 15:37 |
|
|
Current filters on VESC MKIII? by Elwin » Sat, 2021-11-06 11:16 |
7 |
by vadicus Thu, 2022-05-05 01:26 |
|
|
Current KP(Current controller proportional gain) by Geir Henriksen » Tue, 2019-04-30 10:51 |
1 |
by Ricardo Bosqui Tue, 2020-02-11 15:12 |
|
|
Current limit problem by albheim » Fri, 2022-09-09 10:34 |
2 |
by albheim Fri, 2022-09-09 13:24 |
|
|
Current loop resonance in higher ERPM under Current Mode by ypl » Sat, 2019-07-20 09:34 |
0 |
by ypl Sat, 2019-07-20 09:34 |
|
|
Current measurement by Toto » Sun, 2021-02-07 09:12 |
1 |
by skyline1970 Tue, 2021-02-09 19:40 |
|
|
current measurements crazy high after replacing DRV8301 with DRV8302, it throws a FAULT_CODE_ABS_OVER_CURRENT by idkanythinggoes » Thu, 2021-03-18 04:34 |
0 |
by idkanythinggoes Thu, 2021-03-18 04:34 |
|
|
Current mismatch between power supply and vesc tool by mansi712 » Tue, 2024-09-24 13:02 |
0 |
by mansi712 Tue, 2024-09-24 18:08 |
|
|
current proportional pwm signal by grkn5434 » Mon, 2020-02-24 11:42 |
2 |
by grkn5434 Mon, 2020-02-24 15:40 |
|
|
Current Sensing in VESC by Toshi Sharma » Fri, 2021-11-26 08:51 |
17 |
by Toshi Sharma Tue, 2022-01-04 11:46 |
|
|
Current sensor and commanded current by galp » Fri, 2019-02-22 23:08 |
0 |
by galp Fri, 2019-02-22 23:08 |
|
|
Custom application and UART by Dennis Freiburg » Sat, 2020-01-11 13:19 |
3 |
by Dennis Freiburg Sun, 2020-01-12 19:37 |
|
|
Custom Apps on Windows by rok340 » Tue, 2021-01-26 10:05 |
5 |
by rok340 Fri, 2021-01-29 08:33 |
|
|
Custom Built ESC based on VESC 6.6 by jordanlow » Sun, 2020-05-03 16:07 |
3 |
by regskd Tue, 2020-07-28 23:35 |
|
|
Custom code changes- I/O pin go high or low by dsuresh » Thu, 2021-05-13 19:50 |
2 |
by dsuresh Fri, 2021-05-14 22:30 |
|
|
Custom controlling software by neuromancer2701 » Tue, 2018-09-04 02:09 |
4 |
by LogixCraft Mon, 2022-01-03 13:33 |
|
|
Custom Display Receiver for VESC by WatEvsCevs » Wed, 2019-08-28 02:29 |
1 |
by frank Fri, 2019-08-30 10:03 |
|
|
custom firmware by vufmihai » Thu, 2020-01-16 09:06 |
0 |
by vufmihai Thu, 2020-01-16 09:06 |
|
|
Custom VESC4 hardware - disable Regen? by ben5243 » Mon, 2020-04-13 19:48 |
1 |
by hexakopter Sat, 2020-04-18 16:51 |
|
|
Custom-made VESC PCB: High current sensor offset/Overcurrent fault during motor detection, possible hardware/firmware mismatch by Chinmay Mulgund » Mon, 2025-10-13 13:56 |
0 |
by Chinmay Mulgund Mon, 2025-10-13 14:02 |
Log in to post new content in the forum.
