You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Motor won't hold constant speed by Groundspeed100 » Thu, 2024-11-14 05:33 |
0 |
by Groundspeed100 Thu, 2024-11-14 05:33 |
|
|
4 fried vesc's Australia by adamclarke1985 » Tue, 2020-03-31 20:48 |
0 |
by adamclarke1985 Tue, 2020-03-31 21:24 |
|
|
Use IMU for keeping direction by arnolde » Mon, 2024-11-25 11:12 |
0 |
by arnolde Mon, 2024-11-25 11:19 |
|
|
Storing VESC Tool data for later analysis by AidanNowa » Wed, 2024-06-12 15:57 |
0 |
by AidanNowa Wed, 2024-06-12 15:57 |
|
|
Servo Mode / ODrive on VESC by JulianT » Tue, 2020-02-04 09:19 |
0 |
by JulianT Tue, 2020-02-04 09:19 |
|
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees » Tue, 2022-01-18 22:57 |
0 |
by christian.lees Tue, 2022-01-18 22:57 |
|
|
Large robot servo controller with VESC, how to set up position control by kisdia » Thu, 2024-09-19 17:47 |
0 |
by kisdia Thu, 2024-09-19 17:47 |
|
|
Can't Update Firmware by indianboy42 » Mon, 2024-06-17 08:54 |
0 |
by indianboy42 Mon, 2024-06-17 08:54 |
|
|
vesc setup 42V 10A e-bike accu to build in a E-skatboard by olaf2273 » Fri, 2020-04-10 12:33 |
0 |
by olaf2273 Mon, 2020-04-27 15:34 |
|
|
Firmware V4.00 field oriented control motor jerk but wont spin by jordanlow » Thu, 2020-02-13 14:41 |
0 |
by jordanlow Thu, 2020-02-13 14:41 |
|
|
Maximum Motor RPM will not reached by Skyver » Sun, 2022-01-23 10:53 |
0 |
by Skyver Sun, 2022-01-23 10:53 |
|
|
Running PID position Control with FOC sensorless by talabo » Fri, 2021-12-03 17:21 |
0 |
by talabo Fri, 2021-12-03 17:21 |
|
|
Help needed in controlling multiple VESC boards (multiple motors) with VESC ROS (need to debug errors) by shreyas.srinivasan » Thu, 2022-10-13 08:13 |
0 |
by shreyas.srinivasan Thu, 2022-10-13 08:13 |
|
|
VESC 6 EDU: Motor Wizard - Detection failed by Navigator_PJE » Mon, 2022-08-29 16:12 |
0 |
by Navigator_PJE Mon, 2022-08-29 16:12 |
|
|
Encoder maximum PPR/CPR by Michelle90 » Mon, 2022-09-05 22:16 |
0 |
by Michelle90 Mon, 2022-09-05 22:16 |
|
|
How to use an IMU and a PPM remote parallel by Gos1 » Tue, 2022-10-25 15:28 |
0 |
by Gos1 Wed, 2022-10-26 10:57 |
|
|
Maximize startup torque by arosenthal » Sat, 2020-11-14 14:16 |
0 |
by arosenthal Sat, 2020-11-14 14:17 |
|
|
Cannot connect to VESC via USB or SWD by hagis » Wed, 2020-09-23 17:21 |
0 |
by hagis Wed, 2020-09-23 17:21 |
|
|
Issue with VESC I/O on donkey car by baluja » Fri, 2022-10-28 02:56 |
0 |
by baluja Fri, 2022-10-28 02:56 |
|
|
Inquiry about Incremental and Absolute Encoders in VESC for Robotics by sivanhere » Fri, 2022-10-28 21:02 |
0 |
by sivanhere Fri, 2022-10-28 21:02 |
|
|
Voltage spikes on BEMF scope by Sgw32 » Wed, 2020-11-18 16:03 |
0 |
by Sgw32 Wed, 2020-11-18 16:06 |
|
|
What do i need? by Robert Thomas » Fri, 2022-09-16 21:39 |
0 |
by Robert Thomas Fri, 2022-09-16 22:12 |
|
|
Does PLL measure the REAL motor speed by wyk » Mon, 2020-11-23 08:34 |
0 |
by wyk Mon, 2020-11-23 08:34 |
|
|
HFI Tuning - "Start Voltage" Question by drummerboy5408 » Sat, 2022-11-12 03:12 |
0 |
by drummerboy5408 Sat, 2022-11-12 03:12 |
|
|
Dollar signs break private messages by TechAUmNu » Tue, 2018-04-24 18:09 |
0 |
by TechAUmNu Tue, 2018-04-24 18:09 |
Log in to post new content in the forum.
