You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Motor stuttering at lower duty cycle % by trueskyaiways » Thu, 2024-06-20 05:42 |
1 |
by vadicus Fri, 2024-06-21 06:18 |
|
|
Custom VESC4 hardware - disable Regen? by ben5243 » Mon, 2020-04-13 19:48 |
1 |
by hexakopter Sat, 2020-04-18 16:51 |
|
|
EE Senior Design - Controller Code by Flaz » Wed, 2021-12-08 03:22 |
1 |
by jeremy089786 Wed, 2021-12-08 06:19 |
|
|
Alternator custom VESC hardware: Looking for collaborators by jon@ifold » Wed, 2020-01-15 20:11 |
1 |
by frank Thu, 2020-01-16 16:32 |
|
|
Controling the Vesc via Uart and Matlab? by Michael Hamm » Mon, 2022-01-24 16:47 |
1 |
by Fikret Sonmez Sat, 2022-07-30 06:14 |
|
|
Windows 10 free tool wont open... by zip » Tue, 2024-07-02 09:48 |
1 |
by Josiah Eberharter Tue, 2024-07-30 06:41 |
|
|
Isolated CANbus / CAN by shener » Wed, 2024-10-23 15:15 |
1 |
by Markula Thu, 2024-10-24 22:19 |
|
|
What is limiting my RPMS (VESC 4.2 / Q100H setup) by nckbutler » Tue, 2020-03-03 15:37 |
1 |
by socrace Thu, 2020-03-05 03:50 |
|
|
Slow down deacceleration?? by yulaw2k » Tue, 2020-03-17 07:16 |
1 |
by vadicus Wed, 2020-03-18 16:56 |
|
|
Controller just shuts off by Stock88 » Sun, 2024-11-03 03:49 |
1 |
by electricfox Sun, 2024-11-03 09:08 |
|
|
Flipsky 4.2 ESC go BOOM!?! by arranto12 » Thu, 2022-01-06 20:36 |
1 |
by frank Fri, 2022-01-07 10:58 |
|
|
How to connect MPU6050 breakout board to VESC 4.12 by klucznik » Sun, 2020-01-26 19:11 |
1 |
by klucznik Sun, 2020-01-26 22:06 |
|
|
Issues with STR500 tuning and calibration by Swapnil Inamdar » Thu, 2024-08-15 10:39 |
1 |
by electricfox Sun, 2024-08-25 12:00 |
|
|
Issues with running bldc motor (Motor screeching) by mansi712 » Mon, 2024-08-26 12:10 |
1 |
by Nineballshot Mon, 2024-11-25 02:43 |
|
|
Best practice for controlling VESC with high speed PWM by arsenix » Sun, 2022-01-09 18:29 |
1 |
by skyline1970 Wed, 2022-01-19 09:39 |
|
|
Recording VESC parameters by Alexandru Ciocan » Wed, 2020-03-25 08:44 |
1 |
by Jamie42 Wed, 2020-03-25 12:24 |
|
|
VESC 6.05/STR500 ADC1 dead by amblerev » Mon, 2024-11-18 20:02 |
1 |
by electricfox Mon, 2024-11-18 21:06 |
|
|
VESC won't turn on - RED LED by TKnque » Mon, 2022-02-14 01:01 |
1 |
by frank Mon, 2022-02-14 07:48 |
|
|
Need Wiring Diagram for 2xLipo Series with 2x MK3 Button Start by adamchicago » Thu, 2020-01-30 19:47 |
1 |
by frank Sat, 2020-02-01 20:27 |
|
|
Compiling in a different config. by Roger Wolff » Mon, 2018-09-17 17:07 |
1 |
by TechAUmNu Mon, 2018-09-17 17:12 |
|
|
VESC Error "No firmware response" by Magoroth » Tue, 2018-06-12 15:41 |
1 |
by hexakopter Wed, 2018-06-13 01:12 |
|
|
Hello Members! I need suggestions by Scooter Evolution » Mon, 2020-12-07 16:33 |
1 |
by vadicus Tue, 2020-12-08 00:07 |
|
|
Disabling speed cutoff by RDN2003 » Sat, 2020-10-24 00:25 |
1 |
by frank Tue, 2020-10-27 16:42 |
|
|
Raptor 2 by Phill Dixon » Wed, 2018-06-13 18:07 |
1 |
by frank Fri, 2018-06-22 11:35 |
|
|
VESC Hardware link broken by jparadie » Mon, 2018-06-18 12:21 |
1 |
by frank Fri, 2018-06-22 11:33 |
Log in to post new content in the forum.
