You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
360 Rotation Hall Sensors, would these work through ADC? by portnawake » Thu, 2018-06-07 02:37 |
3 |
by Roger Wolff Fri, 2018-06-15 08:50 |
|
|
Sensorless Transition and Deadtime Distortion by vadicus » Wed, 2020-09-16 21:54 |
3 |
by vadicus Tue, 2020-10-13 07:29 |
|
|
Programming NRF51822 Module with ST-Link v2 by koralle » Wed, 2018-07-11 12:06 |
3 |
by koralle Sun, 2018-07-15 01:28 |
|
|
Electric motor from car alternator by frontaleducation » Sun, 2020-11-08 19:39 |
3 |
by frontaleducation Tue, 2020-11-24 14:41 |
|
|
FOCBOX X is not detected by sumedh » Tue, 2022-09-13 22:16 |
3 |
by frank Mon, 2022-09-19 09:18 |
|
|
What temerpature sensor and how do I use it? by evoheyax » Wed, 2018-08-29 19:22 |
3 |
by Danny Bokma Thu, 2018-08-30 19:12 |
|
|
Getting started with bus control of the VESC by Invert » Mon, 2018-05-21 12:04 |
3 |
by PM Thu, 2018-05-31 18:38 |
|
|
FSESC6.6 and Rpi via UART - Understanding the software by gabrielredding » Sat, 2019-07-06 02:50 |
3 |
by abrac Mon, 2019-07-29 14:11 |
|
|
IMU 9250 and 6050 not working on new vesc 4.12 and 4.20 by trung_qly » Sun, 2021-09-05 16:11 |
3 |
by spatsirk Mon, 2025-06-09 18:55 |
|
|
wand brake to reverse by michmg » Tue, 2019-09-10 23:54 |
3 |
by michmg Sat, 2019-09-14 20:16 |
|
|
VESC 75/300 vs VESC 100/250 by XBO » Tue, 2021-09-07 19:31 |
3 |
by flyingbrike Wed, 2021-09-08 13:42 |
|
|
Controlling VESC with arduino - by vulkan66 » Thu, 2019-07-11 11:51 |
3 |
by vulkan66 Thu, 2019-08-01 21:34 |
|
|
I How do I find developers that work with the VESC. by AK6302019 » Sun, 2019-08-04 01:42 |
3 |
by jchillerup Wed, 2019-12-11 09:20 |
|
|
Stutter start by benha » Tue, 2021-08-17 14:30 |
3 |
by flyingbrike Wed, 2021-09-08 13:45 |
|
|
Maximum cable lengths between VESC, battery pack and motor? by sandersesurf » Sun, 2024-01-14 07:55 |
3 |
by bww129 Fri, 2024-03-15 05:46 |
|
|
Set and store Current limit via Canbus by matrixgti » Mon, 2019-08-19 23:13 |
3 |
by Rbz Sun, 2020-05-31 13:44 |
|
|
Input wizard and/or firmware not working for Mini ESC 4.2 with PPM input? by mshipowick » Thu, 2021-06-17 02:08 |
3 |
by mshipowick Thu, 2021-06-24 20:34 |
|
|
How to select COM port by Heimfried » Mon, 2020-05-04 22:23 |
3 |
by Heimfried Wed, 2020-06-10 11:55 |
|
|
Detection failed by Jetboard5 » Sat, 2025-03-22 01:28 |
3 |
by Jetboard5 Sat, 2025-03-22 20:29 |
|
|
Problem with breaking in use in RC plane by fluffy » Tue, 2020-05-26 06:11 |
3 |
by fluffy Sat, 2020-05-30 03:54 |
|
|
Smoked 3 month old VESC - What did I do wrong? by cjjohnson97 » Tue, 2020-04-21 17:40 |
3 |
by cjjohnson97 Fri, 2020-04-24 21:38 |
|
|
Magnetic 3 phase linear motor with VESC by Mr.ironic » Sun, 2020-06-07 18:17 |
3 |
by s0313045 Mon, 2020-06-08 11:41 |
|
|
swap PWM H and PWM L Pins on STM32F4 by Urs_Harry » Tue, 2022-03-15 23:04 |
3 |
by skyline1970 Thu, 2022-03-17 09:58 |
|
|
HELP!!! VESC 4.20 Dual with individual motor control by teit84 » Wed, 2020-06-10 20:03 |
3 |
by TheFallen Thu, 2020-06-18 11:48 |
|
|
Custom Built ESC based on VESC 6.6 by jordanlow » Sun, 2020-05-03 16:07 |
3 |
by regskd Tue, 2020-07-28 23:35 |
Log in to post new content in the forum.
