You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
How do you turn on traction control ( I can't remember) by msim2 » Fri, 2022-05-20 22:06 |
0 |
by msim2 Fri, 2022-05-20 22:06 |
|
VESC 6 Mark III and Traxxas Summit Radio Receiver PWM / PPM Signals by j98221@gmail.com » Fri, 2020-07-03 07:27 |
0 |
by j98221@gmail.com Fri, 2020-07-03 07:27 |
|
My VESC TOOL did not have "balance" by Elijah K » Wed, 2020-08-12 07:52 |
0 |
by Elijah K Wed, 2020-08-12 07:53 |
|
ADC input protection proposal by arestechfinland » Mon, 2020-07-06 19:41 |
0 |
by arestechfinland Mon, 2020-07-06 19:41 |
|
Angle offset detection by Gas_Sn4ke » Mon, 2019-01-21 07:09 |
0 |
by Gas_Sn4ke Mon, 2019-01-21 07:09 |
|
VESC with asynchronous motors by afbbfa » Fri, 2022-07-29 22:51 |
0 |
by afbbfa Fri, 2022-07-29 22:51 |
|
I need clarification on connecting a Magura 0-5k Ohm Pot Twist Throttle to Tronic 250 VESC. by notahorse » Fri, 2022-06-03 08:13 |
0 |
by notahorse Fri, 2022-06-03 08:13 |
|
Regenerative braking in scooter Zero x11 72V dual motor 2 x 1600 w peak power 6000W by Makroman » Wed, 2020-07-08 20:00 |
0 |
by Makroman Wed, 2020-07-08 20:00 |
|
Separate Deadband for ADC2? by striderkent » Wed, 2019-01-23 16:31 |
0 |
by striderkent Wed, 2019-01-23 16:31 |
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 » Mon, 2022-08-01 18:08 |
0 |
by moose09876 Mon, 2022-08-01 18:08 |
|
VESC as generator - settings confirmation by justinlsquire » Mon, 2022-06-06 02:44 |
0 |
by justinlsquire Mon, 2022-06-06 02:44 |
|
VESC Tool Android pairinglist reset with metr.at by nice2cu » Sun, 2020-08-23 12:24 |
0 |
by nice2cu Sun, 2020-08-23 12:24 |
|
FOC vs. BLDC by CTSchorsch » Wed, 2020-07-15 13:15 |
0 |
by CTSchorsch Wed, 2020-07-15 13:15 |
|
Problem with encoder readings with arduino by ruthvikchanda » Thu, 2018-12-06 07:06 |
0 |
by ruthvikchanda Thu, 2018-12-06 10:23 |
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset » Thu, 2022-08-04 01:44 |
0 |
by liminalsunset Thu, 2022-08-04 01:44 |
|
Because..why not: Full Self Riding Skateboard (autonomous skateboard) by x78163 » Wed, 2022-06-08 17:33 |
0 |
by x78163 Wed, 2022-06-08 17:33 |
|
Max eRPM with latest firmware by kubark42 » Fri, 2020-07-17 19:10 |
0 |
by kubark42 Fri, 2020-07-17 19:10 |
|
Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM by PaulMakesThings » Fri, 2022-08-05 11:06 |
0 |
by PaulMakesThings Fri, 2022-08-05 11:06 |
|
BRAND NEW R SPEC DUAL 6355 (4.12 VESC) SET UP ISSUES by rodriguezjoe1@b... » Mon, 2020-09-07 17:50 |
0 |
by rodriguezjoe1@b... Mon, 2020-09-07 17:50 |
|
Making master and slave motors communicate both ways by Sis7 » Tue, 2020-07-21 05:58 |
0 |
by Sis7 Tue, 2020-07-21 05:58 |
|
Best way to run a hoverboard motor that has an AB encoder and Hall sensors, but no index? by PaulMakesThings » Thu, 2022-06-23 23:43 |
0 |
by PaulMakesThings Thu, 2022-06-23 23:43 |
|
resistance and inductance value changes when each measurement by alexshen2012 » Fri, 2022-07-01 05:42 |
0 |
by alexshen2012 Fri, 2022-07-01 05:42 |
|
dual vesc question by badger1666 » Sun, 2018-10-28 12:59 |
0 |
by badger1666 Sun, 2018-10-28 12:59 |
|
Cruise function already implemented? by sam.vanratt » Wed, 2019-01-02 17:05 |
0 |
by sam.vanratt Wed, 2019-01-02 17:20 |
|
Set and measure RPM - Questions by Piep » Thu, 2018-11-08 16:10 |
0 |
by Piep Thu, 2018-11-08 16:10 |
Log in to post new content in the forum.