You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
can not start motor with high duty by qdxiatao » Sat, 2018-03-24 03:58 |
0 |
by qdxiatao Sat, 2018-03-24 03:58 |
|
|
PAS and THROTHLE vesc ! by Sandro luis » Sun, 2023-12-17 17:37 |
0 |
by Sandro luis Sun, 2023-12-17 17:37 |
|
|
Moving from 6s to 12s by scottmahr » Sun, 2023-09-24 22:30 |
0 |
by scottmahr Sun, 2023-09-24 22:30 |
|
|
VESC custom firmware custom UART message by steveyplst » Tue, 2020-08-04 10:23 |
0 |
by steveyplst Tue, 2020-08-04 10:23 |
|
|
Reversed polarity on one of my controllers when setting up by jsherbz92 » Sun, 2025-05-25 15:16 |
0 |
by jsherbz92 Sun, 2025-05-25 15:16 |
|
|
75200 3.3 or 5v short circuit after 10 mins of use by Vassily » Thu, 2025-02-27 23:26 |
0 |
by Vassily Thu, 2025-02-27 23:26 |
|
|
VESC is not working in ADC mode by asnamp » Wed, 2022-04-20 09:21 |
0 |
by asnamp Thu, 2022-04-21 20:11 |
|
|
Windows application by roeebloch » Mon, 2021-04-19 21:08 |
0 |
by roeebloch Mon, 2021-04-19 21:08 |
|
|
VESC Battery voltage discrepancy by Bender » Mon, 2021-03-15 14:23 |
0 |
by Bender Mon, 2021-03-15 14:23 |
|
|
bldc_interface_set_current and bldc_interface_set_rpm troubles by kristof_lr » Wed, 2019-04-24 17:20 |
0 |
by kristof_lr Wed, 2019-04-24 17:20 |
|
|
information to drive 400kv drone motor on ClosedLoop with AS5047 by Syl2078 » Sun, 2019-02-17 19:20 |
0 |
by Syl2078 Sun, 2019-02-17 19:20 |
|
|
Flipsky and Trampa getting two very different detected resistances on same motor! by colmor » Wed, 2025-05-28 22:52 |
0 |
by colmor Wed, 2025-05-28 22:52 |
|
|
Multiple VESCs on the same battery by Riccio » Wed, 2022-04-20 22:09 |
0 |
by Riccio Wed, 2022-04-20 22:09 |
|
|
CAN STATUS INTERRUPTS MOTOR OUTPUT by v1n23nt » Tue, 2022-03-15 09:06 |
0 |
by v1n23nt Tue, 2022-03-15 09:10 |
|
|
Slowing down the speed when in low battery state by dsuresh » Tue, 2021-03-16 21:59 |
0 |
by dsuresh Tue, 2021-03-16 21:59 |
|
|
base on VESC6_MkVI by gavin » Wed, 2025-06-04 15:48 |
0 |
by gavin Wed, 2025-06-04 15:48 |
|
|
Why i cant insert a topic? by SafrdA » Thu, 2021-04-29 20:41 |
0 |
by SafrdA Thu, 2021-04-29 20:41 |
|
|
motor output voltage vs input voltage by rsarver » Wed, 2021-03-17 15:55 |
0 |
by rsarver Wed, 2021-03-17 15:55 |
|
|
Current sensor and commanded current by galp » Fri, 2019-02-22 23:08 |
0 |
by galp Fri, 2019-02-22 23:08 |
|
|
Abs over current error by ogp » Sat, 2025-03-15 22:12 |
0 |
by ogp Sat, 2025-03-15 22:12 |
|
|
Can't download files from my account by STTrife » Sat, 2021-05-01 19:21 |
0 |
by STTrife Sat, 2021-05-01 19:21 |
|
|
Need help with auto power off and ADC by dsuresh » Wed, 2021-03-17 21:45 |
0 |
by dsuresh Wed, 2021-03-17 21:45 |
|
|
When I mount the propeller on the motor ,I get a new promblem by moto_guy » Sat, 2019-03-02 05:16 |
0 |
by moto_guy Sat, 2019-03-02 05:16 |
|
|
Graphing Flux linkage and motor input voltage by stimbog » Mon, 2025-03-17 20:08 |
0 |
by stimbog Mon, 2025-03-17 20:08 |
|
|
VEC 4.20 50A current limitations by Jean-Michel RAVON » Thu, 2021-03-18 14:16 |
0 |
by Jean-Michel RAVON Thu, 2021-03-18 14:16 |
Log in to post new content in the forum.
